Roland V-Synth User Manual

103
Creating and Editing Samples (Sample Mode)
Creating and Editing Samples (Sample Mode)
In this chapter, we will explain the procedures for:
• Sampling (p. 103)
• Editing samples (p. 112)
• Converting samples so the VariPhrase function can be used
(Encoding) (p. 117)
For details on loading samples, refer to p. 133.
Sampling
Settings Before You Sample (What
Is a Template?)
A sampling template is something that holds a collection of settings
for sampling (the setup settings, pre-effect settings, and metronome
settings described below).
You can store eight different sampling templates. When you sample,
you will always select one of these eight templates.
With the factory settings, eight sampling templates are preset.
For details on modifying the settings, refer to “Sampling
Procedure” (p. 104).
Sampling templates are system settings (with the exception of
some metronome parameters). They are remembered even when
you turn off the power. If you wish to restore all eight sampling
templates to the factory settings, perform the Factory Reset
operation (p. 147).
Applications of Each Template
The preset templates cover different input settings and pre-effect
types.
Factory Settings of Each Template
Mic Sample in mono from a mic. Connect a mic to the rear
panel INPUT jack, and set GAIN switch to “MIC.”
Line Sample in stereo from a CD. Connect your CD player to
the rear panel INPUT jacks, and set GAIN switch to
“LINE.”
Coaxial Sample a digital signal. Connect your audio device to
the rear panel COAXIAL IN connector.
Resampl Play a sample on the V-Synth and sample the result.
This is called “resampling.” For details on resampling,
refer to p. 108.
Comp Use the compressor pre-effect. The sample will be re-
corded from the rear panel INPUT jacks.
Limiter Use the limiter pre-effect. The sample will be recorded
from the rear panel INPUT jacks.
MIDI Start sampling when a sequencer start (system realtime
message: FA) is received. The sample will be recorded
from the rear panel INPUT jacks.
USB (XT) Sampling from a PC USB Audio.
* This template is the same as that on the “V-Synth XT,”
which has USB Audio capability. Since the V-Synth
does not have USB Audio capability, the analog input
will automatically be selected as the source if you choose
“USB (XT).”
Setup
Mic Line Coaxial Resampl
SamplingType 1 (MIX) 0 (Stereo) 0 (Stereo) 0 (Stereo)
InputSource 0 (Analog) 0 (Analog) 2 (Coaxial) 3 (Resam-
pling)
TriggerMode 0 (Manual) 2 (Level) 2 (Level) 3 (Note)
TriggerLevel -12 (dB) -12 (dB) -24 (dB) -12 (dB)
PreTrigger 0 (0msec) 0 (0msec) 0 (0msec) 0 (0msec)
PreGain 0 (0dB) 0 (0dB) 0 (0dB) 0 (0dB)
PreFxType 0 (off) 0 (off) 0 (off) 0 (off)
PreFxCS-Sus 0 0 0 0
PreFxCS-Atk 0 0 0 0
PreFxCS-Tone 0 0 0 0
PreFxCS-Lvl 0 0 0 0
PreFxLM-Thr -48 -48 -48 -48
PreFxLM-Rel 0 0 0 0
PreFxLM-Rati 0 0 0 0
PreFxLM-Tone 0 0 0 0
PreFxLM-Lvl 0 0 0 0
PreFxNS-Thr -60 -60 -60 -60
PreFxNS-Rel 0 0 0 0
CountIN 1 (1MES) 0 (0MES) 0 (0MES) 1 (1MES)
MetroType 1 (REC) 1 (REC) 1 (REC) 1 (REC)
Reference_e.book 103 ページ ２００５年３月１０日 木曜日 午後５時６分

Roland V-Synth Specifications

General

Brand	Roland
Model	V-Synth
Category	Electronic Keyboard
Language	English