81
Creating a Patch
Creating a Patch
OSC1/2-LFO-FR/FT:
Formant/Fat LFO Depth (p. 88, p. 91)
OSC1/2-LFO-LVL:
Oscillator Level LFO Depth (p. 91)
CSM1/2-PRM1:
(p. 161)
CSM1/2-PRM2:
(p. 161)
CSM1/2-ENV1-ATK:
COSM Envelope Attack Time (p. 94)
CSM1/2-ENV1-DCY:
COSM Envelope Decay Time (p. 94)
CSM1/2-ENV1-REL:
COSM Envelope Release Time (p. 94)
CSM1/2-ENV2-ATK:
COSM Envelope Attack Time (p. 94)
CSM1/2-ENV2-DCY:
COSM Envelope Decay Time (p. 94)
CSM1/2-ENV2-REL:
COSM Envelope Release Time (p. 94)
CSM1/2-LFO-RATE:
COSM LFO Rate (p. 95)
CSM1/2-LFO-PRM1:
(p. 161)
CSM1/2-LFO-PRM2:
(p. 161)
TVA-LVL:
Level (p. 93)
TVA-ENV-ATK:
TVA Envelope Attack Time (p. 94)
TVA-ENV-DCY:
TVA Envelope Decay Time (p. 94)
TVA-ENV-REL:
TVA Envelope Release Time (p. 94)
TVA-LFO-RATE:
TVA LFO Rate (p. 95)
TVA-LFO-LVL:
Level LFO Depth (p. 93)
TVA-LFO-PAN:
Pan LFO Depth (p. 93)
MFX-SEND:
MFX Send Level (p. 96)
CHO-SEND:
Chorus Send Level (p. 96)
REV-SEND:
Reverb Send Level (p. 96)
MFX1–3:
(p. 166)
TVA-PAN:
Pan (p. 93)
When you touch <List>, the Destination List window will
appear, allowing you to select the Matrix Control Destination
from the list.
Arpeggio
fig.03-11_50
Arpeggio Switch
◆
Switches the Arpeggiator on/off.
Value:
OFF, ON
Patch Tempo
◆
Specify the tempo of an arpeggio. When Clock Source parameter (p.
123) is set to “INTERNAL,” this setting value is effective.
Value:
20.0–250.0
Hold (Arpeggio Hold Switch)
◆
Switch between Hold On/Hold Off for the Arpeggiator
performance.
Value:
OFF, ON
Octave Range (Arpeggio Octave Range)
Sets the key range in octaves over which arpeggio will take place. If
you want the arpeggio to sound using only the notes that you
actually play, set this parameter to “0.” To have the arpeggio sound
using the notes you play and notes 1 octave higher, set this
parameter to “+1.” A setting of “-1” will make the arpeggio sound
using the notes you play and notes 1 octave lower.
Value:
-3– +3
Pattern Edit
Press this when you want to create an original arpeggio pattern.
For details on creating an arpeggio pattern, refer to
“Creating an
Original Arpeggio Pattern (Pattern Edit)”
(p. 63).
KBD Velo (Arpeggio Keyboard Velocity)
Specifies the loudness of the notes that you play.
If you want the velocity value of each note to depend on how
strongly you play the keyboard, set this parameter to “REAL.” If you
want each note to have a fixed velocity regardless of how strongly
you play the keyboard, set this parameter to the desired value (1–
127).
Value:
REAL, 1–127
Reference_e.book 81 ページ ２００５年３月１０日 木曜日 午後５時６分
To Next Page
Loading...
Need help?
General
