Wacker Neuson E09-01 User Manual

3-6 BA 1404 en – Edition 2.7 * * 1404b320.fm
Operation
3.5 Putting into operation
Safety instructions
• Only use the steps and handholds provided when entering and leaving the cabin
• Never use the controls or movable lines and cables as handholds
• Never get on a moving machine. Never jump off the machine
• Refer to the corresponding load diagrams for the boom
Putting into operation for the first time
Important information
• The machine may only be put into operation by authorized personnel!
– see chapter 1.5 Regulations on page 1-5
– see chapter Selection and qualification of personnel, basic responsibilities on
page 2-4
• The personnel must have read and understood this Operator’s Manual before putting
the machine into operation
• The machine may only be used in technically perfect condition in accordance with its desig-
nated use and the instructions set forth in the Operator’s Manual, and only by safety-conscious
persons who are fully aware of the risks involved in operating the machine
• Go through the “Start-up” checklist in the following chapter
Running-in period
Handle the machine carefully during its first 50 operating hours.
The future performance and service life of the machine are heavily dependent on the
observance of the following recommendations during the running-in period.
• Do not change engine speed abruptly
• Avoid using the machine under heavy loads and/or at high speeds.
• Avoid abrupt acceleration, braking and changing travel direction.
• Do not run the engine at high speed for extended periods
• Strictly observe the maintenance schedules in the appendix
– see chapter 5.18 Maintenance plan (overview) on page 5-38

Wacker Neuson E09-01 Specifications

General

Brand	Wacker Neuson
Model	E09-01
Category	Excavators
Language	English

Summary

Safety Instructions

Identification of Warnings and Dangers

Explains warning symbols and terms used in the manual.

Designated Use and Exemption from Liability

Defines the intended purpose and limitations of machine use.

General Conduct and Safety Instructions

Rules for safe operation, organizational measures, and personnel responsibilities.

Safety Instructions Regarding Operation

General rules and precautions for operating the machine safely.

Trailers and Attachments

Transportation

Working in Area of Underground Electric Lines

Safety precautions when working near underground electric lines.

Working Near Overhead Electric Lines

Safety measures for working near overhead electric lines.

Safety Instructions for Maintenance

General safety guidelines for performing maintenance on the machine.

Electrical Energy Hazards

Safety precautions related to the machine's electrical system.

Hydraulic System Safety

Safety precautions when working on the hydraulic system.

Hammer Operation Safety

Specific safety guidelines and precautions for operating the hammer attachment.

Operation

Cabin Overview

Cabin Overview Legend

Instrument Panel Overview

Instrument Panel Overview Legend

Putting into Operation

Critical steps and information for initial machine setup and operation.

Check Lists

Pre-operation checks to ensure the machine is ready and safe.

Driving the Excavator

How to initiate machine movement using drive levers or pedals.

Machine Travel on Slopes

Safety precautions and techniques for operating on slopes.

Stabilizer Blade Operation

Parking the Machine

Procedures for safely parking the machine on level ground.

Parking the Machine on Slopes

Specific safety measures for parking on slopes.

Seat Adjustment

Seat Belt

Instructions for fastening and using the seat belt.

Retracting Belt (Option)

Cab/Canopy Entry and Exit

Battery Master Switch

Towing the Track Excavator

Safety instructions and procedures for towing the machine.

Crane-Lifting the Machine

Loading and Transporting the Machine

Tying Down the Machine

Protective Structures

Shatter Protection for Canopy (Option)

Machine Operation

Fundamental safety rules for operating the excavator.

Control Levers/ISO Controls Overview

Functions and operation of the control levers and pedals.

Changeover Valve for SAE/ISO Controls (Option)

Release Pressure in Operating Hydraulics

Re-equipping Attachments

Procedures for safely attaching and detaching machine implements.

Working with the Standard Bucket

Grading

Working Alongside Trenches

Malfunctions

Engine Trouble

Common engine problems and their possible causes.

Maintenance

Fuel System

Engine Lubrication System

How to check and add engine oil.

Engine Cooling System

How to check and add coolant to the engine cooling system.

Air Filter

V-Belt

Hydraulic System

How to check and add hydraulic oil, and system safety.

Overview of Lubrication Points

Tracks

Electrical System

Battery Safety

General Maintenance

Fluids and Lubricants

Table of recommended fluids and lubricants for various machine components.

Maintenance Plan Overview

Overview of maintenance tasks based on operating hours and intervals.

Technical Data

Engine

Hydraulic System

Operating Hydraulics

Lift Capacity Tables

Tables indicating lifting capacities under various conditions.