Yaesu FTdx5000MP User Manual

Page 126 FTDX5000 OPERATING MANUAL
MODE-CW GROUP
059 A1A R-TYPE
Function: Selects the desired keyer operation mode for
the device connected to the rear panel KEY jack.
Available Values: OFF / BUG / ELEKEY / ACS
Default Setting: ELEKEY
OFF: Disables the rear panel keyer (use this mode
with a straight key, an external keyer, or a
computer-driven keying interface).
BUG: Mechanical “bug” keyer emulation. One
paddle produces “dits” automatically, while
the other paddle manually produces “dahs.”
ELEKEY: Iambic keyer with ACS (Automatic Char-
acter Spacing) disabled.
ACS: Iambic keyer with ACS (Automatic Char-
acter Spacing) enabled.
060 A1A R-REV
Function: Selects the keyer paddle wiring configuration
for the KEY jack on the rear panel.
Available Values: NOR / REV
Default Setting: nor
NOR: Tip = Dot, Ring = Dash, Shaft = Ground
REV: Tip = Dash, Ring = Dot, Shaft = Ground
061 A1A CW AUTO
Function: Enables/disables CW keying while operating
on SSB.
Available Values: OFF / 50M / ON
Default Setting: OFF
OFF: Disables CW keying while operating on SSB.
50M: Enables CW keying only while operating SSB
on 50 MHz (but not HF).
ON: Enables CW keying while operating on SSB (all
TX bands).
NOTE:
This feature allows you to move someone from SSB to
CW without having to change modes on the front panel.
062 A1A BFO
Function: Sets the CW carrier oscillator injection side for
the CW mode.
Available Values: USB / LSB / AUTO
Default Setting: USB
USB: Injects the CW carrier oscillator on the USB
side.
LSB: Injects the CW carrier oscillator on the LSB
side.
AUTO: Injects the CW carrier oscillator on the LSB
side while operating on the 7 MHz band and
below, and the USB side while operating on
the 10 MHz band and up.
MENU MODE
053 A1A LCUT FRQ
Function: Selects the cutoff frequency of the lower side
of the RX audio filter in the CW mode.
Available Values: OFF / 100 Hz ~ 1000Hz (50 Hz/step)
Default Setting: 300Hz
054 A1A LCUT SLP
Function: Selects the filter slope of the lower side of the
RX audio filter in the CW mode.
Available Values: 6dB/oct or 18dB/oct
Default Setting: 18dB/oct
055 A1A HCUT FRQ
Function: Selects the cutoff frequency of the upper side
of the RX audio filter in the CW mode.
Available Values: OFF / 700Hz ~ 4000Hz (50 Hz/step)
Default Setting: 1000Hz
056 A1A HCUT SLP
Function: Selects the filter slope of the upper side of the
RX audio filter in the CW mode.
Available Values: 6dB/oct or 18dB/oct
Default Setting: 6dB/oct
057 A1A F-TYPE
Function: Selects the desired keyer operation mode for
the device connected to the front panel KEY jack.
Available Values: OFF / BUG / ELEKEY / ACS
Default Setting: ELEKEY
OFF: Disables the front panel keyer (use this
mode with a straight key, an external keyer,
or a computer-driven keying interface).
BUG: Mechanical “bug” keyer emulation. One
paddle produces “dits” automatically, while
the other paddle manually produces “dahs.”
ELEKEY: Iambic keyer with ACS (Automatic Char-
acter Spacing) disabled.
ACS: Iambic keyer with ACS (Automatic Char-
acter Spacing) enabled.
058 A1A F-REV
Function: Selects the keyer paddle’s wiring configuration
for the KEY jack on the front panel.
Available Values: NOR / REV
Default Setting: nor
NOR: Tip = Dot, Ring = Dash, Shaft = Ground
REV: Tip = Dash, Ring = Dot, Shaft = Ground

Yaesu FTdx5000MP Specifications

General

Brand	Yaesu
Model	FTdx5000MP
Category	Transceiver
Language	English