Yaesu FTdx5000MP User Manual

Page 97FTDX5000 OPERATING MANUAL
CONTEST MEMORY KEYER
7. When the message is complete, add the “}” character
at the end to signify the termination of the message.
8. Press and hold in the FH-2
[
MEM
]
key
for 2 seconds to exit, once all charac-
ters (including “}”) have been pro-
grammed.
CHECKING THE CW MEMORY CONTENTS
1. Be sure that Break-in is still turned “off” by the
[
BK-
IN
]
button.
2. Press the
[
MONI
]
button briefly, to enable the CW
monitor.
3. Press an FH-2
[
1
]
~
[
5
]
key to check
your work. You will hear the stored
message with the CW monitor sidetone,
but no RF energy will be transmitted.
NOTE:
Adjust the monitor level using the
[
MONI
]
knob.
ON-THE-AIR CW MESSAGE PLAYBACK
1. Press the
[
BK-IN
]
button briefly to enable transmis-
sion. Either Full- or Semi-break-in will be engaged de-
pending on the setting of Menu item “063 A1A BK-
IN.”
2. Press the FH-2’s
[
1
]
~
[
5
]
key to trans-
mit the programmed message.
NOTE:
If you subsequently decide to use the “Message Memory”
technique for message storage, on a particular memory
register, the contents of the message stored using text in-
put will not be transferred over when you select the “Mes-
sage Memory” technique (the Menu Mode Setting is set
to “MESSAGE”).
Contest Number Programming
Use this process if you are starting a contest, or if
you somehow get out of sync with the proper num-
ber in the middle of a contest.
1. Press the
[
MENU
]
button briefly, to enter the
Menu mode.
2. Rotate the
(
VFO-A
)[
SELECT
]
knob to select
Menu item “024 KEY CONTEST”.
3. Rotate the
(
VFO-B
)[
SELECT
]
knob to set the
Contest Number to the desired value.
ADVICE:
Press the
[
CLEAR
]
button briefly (located
above the
[
CLAR
(
VFO-B
)]
knob), to reset the
Contest Number to “1”.
4. Press and hold in the
[
MENU
]
button for two
seconds to store the new number and exit to
normal operation.
CW CONVENIENCE FEATURES
LOCK
OFFON
LOCK
OFFON
LOCK
OFFON
LOCK
OFFON
Decrementing the Contest Number
Use this process if the current contest number gets
ahead of the actual number you want to send (in
case of a duplicate QSO, for example).
Press the FH-2 control’s
[
DEC
]
key.
The current Contest Number will be
reduced by one. Press the
[
DEC
]
button briefly, as many times as nec-
essary, to reach the desired number.
If you go too far, use the “Contest
Number Programming” technique
desireded at the left.
TEXT
!
“””
#
$
%
&
‘’’
CW CODE
SN
AF
---
SX
KA
AS
WG
TEXT
(
“
)
”
*
+
,
---
.
CW CODE
KN
KK
---
AR
MIM
DU
AAA
TEXT
/
“:”
;
<
=
>
?
CW CODE
DN
OS
KR
---
BT
---
IMI
TEXT
@
“
[
”
\
]
^
_
‘
}
’
CW CODE
@
---
AL
---
---
IQ
---

Yaesu FTdx5000MP Specifications

General

Brand	Yaesu
Model	FTdx5000MP
Category	Transceiver
Language	English