Yealink SIP-T53W Administrator's Guide

Administrator’s Guide for SIP-T2 Series/T4 Series/T5 Series/CP920 IP Phones
399
Menu > Settings > Advanced Settings (default password: admin) > FWD International > FWD Inter-
national
Parameter
forward.idle_access_always_fwd.enable <y0000000000xx>.cfg
Description
It enables or disables the phone to always enter the Always Forward setting screen when pressing
the Forward key on the Idle screen.
Permitted
Values
0-Disabled. When pressing the Forward key, the phone may activate/deactivate the call forward or
enter the Always Forward/Busy Forward/No Answer Forward setting screen.
1-Enabled
Default
0
Parameter
features.fwd_diversion_enable <y0000000000xx>.cfg
Description
It enables or disables the phone to present the diversion information when an incoming call is for-
warded to the IP phone.
Permitted
Values
0-Disabled
1-Enabled, the server can use the Diversion field with a SIP header to inform the phone of a call’s his-
tory.
Default
1
Web UI
Features > General Information > Diversion/History-Info
Call Forward Feature Configuration
After you choose a call forward mode, you can configure call forward feature for all lines or specific lines. It depends
on the call forward mode (T19(P) E2/CP920 except):
l
Phone (default): Call forward feature is effective for all lines.
l
Custom: Call forward feature can be configured for a specific line or multiple lines.
Note: Forward mode is set by the parameter “features.fwd_mode”.
Yealink phones also support call forward on code and off code to activate and deactivate server-side call forward
feature. They may vary on different servers.
Tip: You can set a DSS key as a Forward key, and specify a contact you want to forward the incoming calls to for this key.
For more information, refer to DSS Keys.
Topics
Call Forward in Phone Mode Configuration
Call Forward in Custom Mode Configuration
Call Forward in Phone Mode Configuration
The following table lists the parameters you can use to configure call forward in phone mode.
Parameter
forward.always.enable <y0000000000xx>.cfg
Description
It triggers the always forward feature to on or off on a phone basis.
Note: It works only if “features.fwd.allow” is set to 1 (Enabled) and “features.fwd_mode” is set to 0
(Phone) (except T19(P) E2/CP920 phones).
Permitted
Values
0-Off
1-On, incoming calls are forwarded to the destination number (configured by the parameter “for-
ward.always.target”) immediately.

Yealink SIP-T53W Specifications

General

Mounting	Desk/Wall
Handset type	Wired handset
Product type	IP mobile phone
Product color	Gray
Keypad illumination	Yes
Wi-Fi standards	802.11a, 802.11g, Wi-Fi 4 (802.11n)
Bluetooth version	4.2
Security algorithms	AES, HTTPS, SIPS
Networking standards	IEEE 802.1p, IEEE 802.1x, IEEE 802.3af
Ethernet LAN interface type	Gigabit Ethernet
Supported network protocols	FTP/TFTP/HTTP/HTTPS
Dual-Tone Multi-Frequency (DTMF) modes	In-band, Out-of band, SIP info
USB 2.0 ports quantity	1
Ethernet LAN (RJ-45) ports	2
Lines quantity	8 lines
Phonebook capacity	1000 entries
Number of VoIP accounts	12
AC adapter input voltage	100 - 240 V
AC adapter output current	1.2 A
AC adapter output voltage	5 V
Power consumption (typical)	2.3 W
Volume control	Buttons
Number of programmable keys	8
Storage temperature (T-T)	-30 - 70 °C
Operating temperature (T-T)	0 - 40 °C
Operating relative humidity (H-H)	10 - 95 %
Display diagonal	3.7 \
Display resolution	360 x 160 pixels
Cables included	LAN (RJ-45)
Number of handles included	1 pc(s)
Number of DECT wireless handsets	4
Voice codecs	G.722, G.723.1, G.726, G.729A, G.729B, OPUS, iLBC

Weight and Dimensions

Depth	210.6 mm
Width	212 mm
Height	174.5 mm