Cisco 2911 Configuration Guide

213
Cisco 3900 Series, Cisco 2900 Series, and Cisco 1900 Series Integrated Services Routers Generation 2 Software Configuration Guide
Chapter Configuring Multi-Gigabit Fabric Communication
Cisco High-Speed Intrachassis Module Interconnect (HIMI)
• NME-XD-48ES-2S-P
• NME-XD-24ES-1S-P
See the Cisco EtherSwitch Feature Guide documentation at Cisco.com for configuration details,
http://www.cisco.com/en/US/docs/ios/12_3t/12_3t14/feature/guide/miragenm.html#wp1787811.
Cisco High-Speed Intrachassis Module Interconnect (HIMI)
Cisco 3900 series and Cisco 2900 series routers use Cisco High-Speed Intrachassis Module Interconnect
(HIMI) to support SM-to-SM or SM-to-ISM communication through the MGF.
Use the connect connection-name module Module1 Channel-id1 module Module2 Channel-id2
command to establish a maximum of two HIMI connections on the Cisco 3900 series ISR routers and
one HIMI connection on Cisco 2900 series andCisco 1900 series ISRs. Module 1 and Module 2 are the
slot/port of the two modules. The Channel-id1 and Channel-id2 variables must always have a value of 0.
When two modules are configured in a HIMI connection, the modules cannot send traffic to any other
module except its HIMI-dedicated partner.
See Cisco High-Speed Intrachassis Module Interconnect (HIMI) Configuration Guide at Cisco.com for
detailed configuration instructions,
http://www.cisco.com/en/US/docs/ios/12_4/12_4_mainline/srdesfm1.html.
Note See the module documentation to validate HIMI support.
Using HIMI for VLAN Traffic Flows
For HIMI configurations, the port-level VLAN memberships are ignored on the Multi-Gigabit Fabric
(MGF). Use the connect connection-name module module1 vlan-id module module2 command to
redirect VLAN traffic flows from SM-to-SM or SM-to-ISM connections on the MGF.
The following two modules, as well as others, support VLAN traffic redirection:
• Cisco Etherswitch service module
• Cisco Services Ready Engine internal service module (ISM-SRE)
Note See the module documentation to validate HIMI support.

Cisco 2911 Specifications

General

Ethernet LAN	Yes
Cabling technology	10/100/1000Base-T(X)
Networking standards	IEEE 802.1Q, IEEE 802.1ag, IEEE 802.3, IEEE 802.3ab, IEEE 802.3af, IEEE 802.3ah, IEEE 802.3u
Ethernet LAN data rates	10, 100, 1000 Mbit/s
Ethernet interface type	Gigabit Ethernet
DHCP client	-
Routing protocols	BGP, EIGRP, OSPF
Supported protocols	IPv4, IPv6, IS-IS, IGMPv3, PIM SM, SSM, DVMRP, IPSec, GRE, BVD, MPLS, L2TPv3, PPP, MLPPP, MLFR, HDLC, RS-232, RS-449, X.21, V.35, EIA-530, PPPoE, ATM
USB version	2.0
RS-232 ports	1
Expansion slots	4 x EHWIC 2 x DSP 1 x ISM
USB ports quantity	2
Ethernet LAN (RJ-45) ports	3
Firewall security	Cisco IOS
Input current	2.2 A
AC input voltage	100 - 240 V
Power source type	AC
AC input frequency	47 - 63 Hz
Power consumption (typical)	50 W
Product color	Black
Rack capacity	2U
Operating altitude	0 - 4000 m
Non-operating altitude	0 - 4570 m
Storage temperature (T-T)	-40 - 80 °C
Operating temperature (T-T)	0 - 40 °C
Storage relative humidity (H-H)	5 - 95 %
Operating relative humidity (H-H)	5 - 85 %
Safety	UL 60950-1, CAN/CSA C22.2 No. 60950-1, EN 60950-1, AS/NZS 60950-1, IEC 60950-1
Electromagnetic compatibility	47 CFR, ICES-003, EN55022, CISPR22, AS/NZS 3548, VCCI V-3, EN 300-386, EN 61000, EN 55024, CISPR 24EN50082-1

Weight and Dimensions

Depth	304.8 mm
Width	438.2 mm
Height	88.9 mm
Weight	8200 g