Emerson Bettis 500 User Manual

February 2018
Installation and Operation Manual
E2K-405-0218 Rev. 2
74
Section 6: Troubleshooting
Troubleshooting
6.2.1 Display Alarm Log
At the time the alarm occurs, the alarm is displayed on the bottom line of the
message center. This display lists the last nine alarms that have occurred. The rst
alarm listed is the most recent to occur. The alarm list progresses from the most
recent to the oldest. The following alarms may be displayed.
EFM MONITOR OPEN INHIBIT
OPEN TORQUE_% CLOSE INHIBIT
CLOSE TORQUE_% LOCAL ESD
VALVE STALLED REMOTE ESD
VALVE DRIFT LOST AIN1 SIGNAL
POWER FAIL ACTUATOR FAIL
LOST PHASE SETUP ERROR
MOTOR OVERLOAD SET LIMITS BEFORE OPERATING
NOTE:
When the “SET LIMITS BEFORE OPERATING” alarm is displayed, no other alarms
will be displayed until the limits are set.
1. At the “DISPLAY ALARM LOG?” prompt, answer “YES.”
2. Use the selector knob (NEXT/BACK) to review the alarms. See Figure 6-2.
NOTE:
The control knob (YES/NO) can be used to view the alarms however do
not cycle the control knob between NO and YES because the unit could
display the “SETUP” mode.
3. Use the control knob (NO) to exit the display.
Figure 6-2 Display Alarm Log Example
NO
YESYES
NO
YES YES
NO
Analog
<analog_state>
<state: NORMAL/
NOT CONFIGURED/
UNDER RANGE/
OVER RANGE>
Network
<network_state>
<state: NORMAL/
NOT CONFIGURED/
SPI LINK LOST/ACM
FAILED/HOST LOST
EFM
<efm_state>
<state: NORMAL/
SHUTDOWN/
FAILED>
Refresh every
30 seconds
BACK
YES
DISPLAY
ALARM LOG?
DISPLAY ALARM LOG
Figure 6-2
Go to
Figure 6-1
DISPLAY TORQUE PROFILE
Figure 6-3
NO
OR
NEXT
NO
OR
NEXT
BACK
NEXT
NO NO
YES
1 <alarm 1>
2 <alarm 2>
YES YES
DISPLAY
TORQUE PROFILE
Pull-out
Torque
<xx>%
YES
3 <alarm 3>
4 <alarm 4>
NO
YES
5 <alarm 5>
6 <alarm 6>
NO
YES
7 <alarm 7>
8 <alarm 8>
NO
YES
9 <alarm 9>
10 <alarm 10>
YES
DISPLAY
OPERATE LOG?
DISPLAY OPERATION LOG
Figure 6-4
DISPLAY HARDWARE
Figure 6-6
NO
OR
NEXT
BACK
NEXT
NO NO
YES
Motor
Starts
<xxx,xxx,xxx>
YES
NO
YES
YES
BACK
NEXT
NO
NO
NO
NO
YES
@10 Torque =
<xx>%
@20 Torque =
<xx>%
Display Open
Torque
Profile?
YES
NO
YES
NO
YES YES
YES
NO
@30 Torque =
<xx>%
@40 Torque =
<xx>%
@50 Torque =
<xx>%
@60 Torque =
<xx>%
@70 Torque =
<xx>%
@80 Torque =
<xx>%
@90 Torque =
<xx>%
YES
NO
YES
@10 Torque =
<xx>%
@20 Torque =
<xx>%
Display Close
Torque
Profile?
YES
NO
YES
NO
YES
NO
@30 Torque =
<xx>%
@40 Torque =
<xx>%
@50 Torque =
<xx>%
@60 Torque =
<xx>%
@70 Torque =
<xx>%
@80 Torque =
<xx>%
@90 Torque =
<xx>%
NO
OR
NEXT
YES
Pull-out
Torque
<xx>%
YES
BACK
NEXT
NO
NO
NO
NO
NO
NO
YES
@10 Torque =
<xx>%
@20 Torque =
<xx>%
Display Open
Torque
Archive?
YES
NO
YES
NO
YES YES
YES
NO
@30 Torque =
<xx>%
@40 Torque =
<xx>%
@50 Torque =
<xx>%
@60 Torque =
<xx>%
@70 Torque =
<xx>%
@80 Torque =
<xx>%
@90 Torque =
<xx>%
YES
NO
YES
@10 Torque =
<xx>%
@20 Torque =
<xx>%
Display Close
Torque
Archive?
YES
NO
YES
NO
YES
NO
@30 Torque =
<xx>%
@40 Torque =
<xx>%
@50 Torque =
<xx>%
@60 Torque =
<xx>%
@70 Torque =
<xx>%
@80 Torque =
<xx>%
@90 Torque =
<xx>%
DISPLAY
TORQUE ARCHIVE
NO
OR
NEXT
YES
REMOTE
DISPLAY#2
<rem_disp#2_state>
<state: NORMAL/
NOT CONFIGURED/
LOST LINK/FAILED>
YES
BACK
NEXT
NO
NO
NO
NONO
YES
APD Module
<apd_state>
<state: NORMAL/
FAILED>
Inside
Temperature=
<xx>C
YES
NO
YES YES
NO
DISPLAY
HARDWARE?
EXIT?
Strokes
<xxx,xxx,xxx>
Motor
Run Time
<hr:min:sec>
YES
DISPLAY
OPERATE ARCHIVE?
DISPLAY OPERATION ARCHIVE
Figure 6-5
NO
OR
NEXT
BACK
NEXT
NO NO
YES
Motor
Starts
<xxx,xxx,xxx>
YES
NO
YES
Strokes
<xxx,xxx,xxx>
Motor
Run Time
<hours>
Central Control
<cen_ctrl_state>
<state: NORMAL/
LOST LINK /FAILED>
Local Display
<lcl_disp_state>
<state: NORMAL/
LOST LINK /FAILED>
REMOTE
DISPLAY#1
<rem_disp#1_state>
<state: NORMAL/
NOT CONFIGURED/
LOST LINK / FAILED>

Emerson Bettis 500 Specifications

General

Brand	Emerson
Model	Bettis 500
Category	Controller
Language	English