Emerson Bettis 500 User Manual

February 2018
Installation and Operation Manual
E2K-405-0218 Rev. 2
76
Section 6: Troubleshooting
Troubleshooting
6.2.3 Display Torque Archive
Torque archive is displayed like Torque Prole. Torque archive is the data stored at
the time commanded by the user in the “CHANGE SETTINGS” mode. See Section
5.5.2, Valve Control Setup and Figure 5-6.
1. At the “DISPLAY TORQUE ARCHIVE?” prompt, answer “YES.”
2. See Section 6.2.2, Display Torque Profile, and Figure 6-3.
6.2.4 Display Operation Log
Operation log aids in troubleshooting because it contains the operation data
accumulated since the operation log was reset. See Figure 6-4.
1. At the “DISPLAY OPERATE LOG?” prompt, answer “YES.”
2. Use the control knob (YES) to review the operate log.
Motor starts value is the number of times the motor has been started. The strokes
value displayed is the number of full strokes from limit to limit. Stroke time can be
measured as follows:
1. Reset operation log.
2. Stroke the valve. Stroke time is equal to the motor run time.
Motor run time is the total motor operational time.
To reset operation log:
1. Enter “Change Settings” mode.
2. Select “VALVE CONTROL SETUP?”
See Section 5.5.2, Valve Control Setup
Figure 6-4 Display Operation Log
NO
YESYES
NO
YES YES
NO
Analog
<analog_state>
<state: NORMAL/
NOT CONFIGURED/
UNDER RANGE/
OVER RANGE>
Network
<network_state>
<state: NORMAL/
NOT CONFIGURED/
SPI LINK LOST/ACM
FAILED/HOST LOST
EFM
<efm_state>
<state: NORMAL/
SHUTDOWN/
FAILED>
Refresh every
30 seconds
BACK
YES
DISPLAY
ALARM LOG?
DISPLAY ALARM LOG
Figure 6-2
Go to
Figure 6-1
DISPLAY TORQUE PROFILE
Figure 6-3
NO
OR
NEXT
NO
OR
NEXT
BACK
NEXT
NO NO
YES
1 <alarm 1>
2 <alarm 2>
YES YES
DISPLAY
TORQUE PROFILE
Pull-out
Torque
<xx>%
YES
3 <alarm 3>
4 <alarm 4>
NO
YES
5 <alarm 5>
6 <alarm 6>
NO
YES
7 <alarm 7>
8 <alarm 8>
NO
YES
9 <alarm 9>
10 <alarm 10>
YES
DISPLAY
OPERATE LOG?
DISPLAY OPERATION LOG
Figure 6-4
DISPLAY HARDWARE
Figure 6-6
NO
OR
NEXT
BACK
NEXT
NO NO
YES
Motor
Starts
<xxx,xxx,xxx>
YES
NO
YES
YES
BACK
NEXT
NO
NO
NO
NO
YES
@10 Torque =
<xx>%
@20 Torque =
<xx>%
Display Open
Torque
Profile?
YES
NO
YES
NO
YES YES
YES
NO
@30 Torque =
<xx>%
@40 Torque =
<xx>%
@50 Torque =
<xx>%
@60 Torque =
<xx>%
@70 Torque =
<xx>%
@80 Torque =
<xx>%
@90 Torque =
<xx>%
YES
NO
YES
@10 Torque =
<xx>%
@20 Torque =
<xx>%
Display Close
Torque
Profile?
YES
NO
YES
NO
YES
NO
@30 Torque =
<xx>%
@40 Torque =
<xx>%
@50 Torque =
<xx>%
@60 Torque =
<xx>%
@70 Torque =
<xx>%
@80 Torque =
<xx>%
@90 Torque =
<xx>%
NO
OR
NEXT
YES
Pull-out
Torque
<xx>%
YES
BACK
NEXT
NO
NO
NO
NO
NO
NO
YES
@10 Torque =
<xx>%
@20 Torque =
<xx>%
Display Open
Torque
Archive?
YES
NO
YES
NO
YES YES
YES
NO
@30 Torque =
<xx>%
@40 Torque =
<xx>%
@50 Torque =
<xx>%
@60 Torque =
<xx>%
@70 Torque =
<xx>%
@80 Torque =
<xx>%
@90 Torque =
<xx>%
YES
NO
YES
@10 Torque =
<xx>%
@20 Torque =
<xx>%
Display Close
Torque
Archive?
YES
NO
YES
NO
YES
NO
@30 Torque =
<xx>%
@40 Torque =
<xx>%
@50 Torque =
<xx>%
@60 Torque =
<xx>%
@70 Torque =
<xx>%
@80 Torque =
<xx>%
@90 Torque =
<xx>%
DISPLAY
TORQUE ARCHIVE
NO
OR
NEXT
YES
REMOTE
DISPLAY#2
<rem_disp#2_state>
<state: NORMAL/
NOT CONFIGURED/
LOST LINK/FAILED>
YES
BACK
NEXT
NO
NO
NO
NONO
YES
APD Module
<apd_state>
<state: NORMAL/
FAILED>
Inside
Temperature=
<xx>C
YES
NO
YES YES
NO
DISPLAY
HARDWARE?
EXIT?
Strokes
<xxx,xxx,xxx>
Motor
Run Time
<hr:min:sec>
YES
DISPLAY
OPERATE ARCHIVE?
DISPLAY OPERATION ARCHIVE
Figure 6-5
NO
OR
NEXT
BACK
NEXT
NO NO
YES
Motor
Starts
<xxx,xxx,xxx>
YES
NO
YES
Strokes
<xxx,xxx,xxx>
Motor
Run Time
<hours>
Central Control
<cen_ctrl_state>
<state: NORMAL/
LOST LINK /FAILED>
Local Display
<lcl_disp_state>
<state: NORMAL/
LOST LINK /FAILED>
REMOTE
DISPLAY#1
<rem_disp#1_state>
<state: NORMAL/
NOT CONFIGURED/
LOST LINK / FAILED>

Emerson Bettis 500 Specifications

General

Brand	Emerson
Model	Bettis 500
Category	Controller
Language	English