Kyocera TASKalfa 2201 User Manual

10-14
Appendix > Paper
Hagaki
Before loading Hagaki into the multi purpose tray, fan them and align the edges. If the Hagaki paper is curled, straighten
it before loading. Printing onto curled Hagaki may cause jams.
Use unfolded Oufukuhagaki (available at post offices). Some Hagaki may still have rough edges developed by a paper
cutter on the back side. Remove any such rough edges by placing the Hagaki on a flat surface and rubbing the edges
gently a few times with a ruler.
Envelopes
Use the multi purpose tray for envelopes.
Due to the structure of envelopes, printing evenly over the entire surface may not be possible in some cases. Thin
envelopes in particular may be wrinkled by the machine in some cases as they pass through. Before purchasing
envelopes in volume, try testing a sample to ensure the print quality.
Storing envelopes for a long period may cause them to become wrinkled. Thus, keep the package sealed until you are
ready to use them.
Keep the following points in mind.
• Do not use envelopes with exposed adhesive. In addition, do not use the type of envelope in which the adhesive is
exposed after the top layer is peeled off. Serious damage may be caused if the paper covering the adhesive comes
off in the machine.
• Do not use envelopes with certain special features. For example, do not use envelopes with a grommet for winding a
string to close the flap or envelopes with an open or film-covered window.
• If paper jams occur, load fewer envelopes at once.
• To prevent paper jams when printing onto multiple envelopes, do not allow more than ten envelopes to remain in the
Inner tray at once.
Thick Paper
Before loading thick paper in the multi purpose tray, fan it and align the edges. Some thick paper may still have rough
edges developed by a paper cutter on the back side. Remove any such rough edges just as with Hagaki by placing the
paper on a flat surface and rubbing the edges gently a few times with a ruler. Printing onto paper with rough edges may
cause jams.
Colored Paper
Colored paper must conform to the specifications listed on page 10-8. In addition, the pigments in the paper must be
able to withstand the heat of printing (up to 200°C or 392°F).
NOTE
If the paper is not supplied correctly even after it is smoothed, load the paper in the multi purpose tray with the leading
edge raised a few millimeters.
Burrs
Burrs

Kyocera TASKalfa 2201 Specifications

General

Duplex printing	Yes
Print technology	Laser
Maximum resolution	600 x 600 DPI
Time to first page (black, normal)	5.7 s
Print speed (black, normal quality, A3)	10 ppm
Print speed (black, normal quality, A4/US Letter)	22 ppm
Copier resize	25 - 400 %
Maximum number of copies	999 copies
Scan to	E-mail, Image
Scan drivers	TWAIN
Grayscale levels	256
Image formats supported	BMP, JPG, TIF
Document formats supported	PDF
Faxing	Mono faxing
Modem speed	33.6 Kbit/s
Fax coding methods	MH, MMR (Fax coding method), MR
Fax resolution (black)	200 x 100 DPI
Fax transmission speed	4 sec/page
Digital sender	-
Printing colors	Black
Maximum duty cycle	- pages per month
Number of print cartridges	1
Processor family	ARM
Card reader integrated	No
Sound pressure level (printing)	62 dB
Sound pressure level (quiet mode)	40 dB
Paper input type	Cassette, Paper tray
Total input capacity	400 sheets
Total output capacity	250 sheets
Maximum input capacity	1300 sheets
Multi-Purpose tray input capacity	100 sheets
Paper tray media types	Plain paper
Paper tray media weight	64 - 105 g/m²
ISO A-series sizes (A0...A9)	A3, A4, A5
Maximum ISO A-series paper size	A3
Multi-Purpose Tray media weight	45 - 160 g/m²
Market positioning	Business
Standard interfaces	USB 2.0
AC input voltage	220 - 240 V
AC input frequency	50 - 60 Hz
Power consumption (standby)	76 W
Power consumption (PowerSave)	1.54 W
Power consumption (average operating)	415 W
Certification	TÜV/GS, CE

Weight and Dimensions

Depth	527 mm
Width	565 mm
Height	485 mm