Roland FA-07 User Manual

44
Editing a Studio Set
Overall Settings for the Studio Set
Here’s how to make settings that apply to the entire studio set.
1. Press the [MENU] button.
2. Move the cursor to “Studio Set Common” and press the
[ENTER] button.
The STUDIO SET COMMON screen appears.
MEMO
From the STUDIO SET PLAY screen, you can also access the
STUDIO SET COMMON screen by holding down the [SHIFT]
button and pressing the [5] (Studio Common) button.
3. Use the cursor buttons to select an item, and use the dial
to edit the setting.
NOTE
The edits you make to the studio set are temporary. They will be
lost if you turn o the power or select another studio set. If you
want to keep the changes, save the studio set (p. 45).
Common Parameters
MEMO
For details on the common parameters, refer to “Parameter
Guide” (PDF).
Tab Explanation
General
Specify the play mode, pad part, and the drum part
to which Comp+EQ applies.
Control
Specify the MIDI messages used to control
parameters when using tone control 1–4.
Phase Lock
Turn this “on” if you want to minimize inconsistency
between the note-on timing of parts that are played
on the same MIDI channel.
Pedal
Specify the MIDI messages used to control
parameters when using a pedal connected to the
CTRL 1 and CTRL 2 jacks.
S1/S2
Specify the MIDI messages used to control
parameters when using the [S1] [S2] buttons.
Knob
Specify the MIDI messages used to control
parameters when using the SOUND MODIFY knobs.
D-Beam
Specify the MIDI messages used to control
parameters when using the D-BEAM controller.
Control Sw
For each part, specify whether various controller
operations will be enabled (ON) or disabled (OFF).
Settings for Each Part
A studio set has 16 parts; each part has its own settings such as
volume (Level), equalizer (EQ), and key range (Keyboard).
1. Access the PART VIEW screen (p. 26).
2. Use the cursor buttons to select a parameter, and use the
dial to edit the value.
To switch tabs, hold down the [SHIFT] button and use the cursor
[
] [ ] buttons.
Part parameters
MEMO
For details on the part parameters, refer to “Parameter Guide”
(PDF).
Tab Explanation
Level/Pan
Specify each part’s tone, level, pan, and MIDI receive
settings.
Keyboard
Specify each part’s key range, and whether the
arpeggiator is applied.
Output/EFX
Specify each part’s output destination, and the level
of signal that is sent to chorus and reverb.
EQ Edit the equalizer that is applied to each part.
Pitch Specify each part’s pitch and portamento setting.
Scale Tune Specify the scale tune settings of each part.
Vibrato Edit each part’s vibrato settings.
Oset
Specify osets for parameters such as cuto and
resonance.
Mono/Poly/Legato Edit each part’s mono, poly, and legato settings.
Voice Reserve
Specify the number of voices that are reserved for
each part.
MIDI Rx Filter
Specify the MIDI messages that are received by each
part.
* Depending on the sound, some part parameters have no eect.

Roland FA-07 Specifications

General

Control type	Buttons
Backlight color	Red
Backlight buttons	Yes
MIDI-keyboard number of keys	76 keys
Product color	Black
Display type	LCD
Display diagonal	5 \
Interface	USB
Headphone outputs	1
USB ports quantity	2
Compatible memory cards	SDHC
6.35 mm (1⁄4-inch) output	3
Power source type	AC
Bit rate	16 bit
Product type	Digital synthesizer
Keyboard number of keys	76
Maximum polyphony (notes)	128
Reverberation effects quantity	6

Weight and Dimensions

Depth	311 mm
Width	1231 mm
Height	107 mm
Weight	8500 g