142
Error messages
If an incorrect operation is performed, or if processing could not be performed as you specified, an error message will appear. Refer
to the explanation for the error message that appears, and take the appropriate action.
Message
Meaning Cause/Action
Beat Differs!
While using the Pattern Edit operation Copy (p. 71),
the copy could not be executed since the copy-source
and copy-destination patterns have differing time sig-
natures.
You must copy between patterns that have the same time sig-
nature.
Cannot Assign
Phrase!
Since there are two or more unmuted parts, the phrase
cannot be registered in an RPS set.
Choose one part of the phrase that you want to register, and
mute all of the remaining parts (p. 45).
Cannot Assign
Sample!
Since there are no empty parts, you can’t assign a sam-
ple.
Sample into a pattern that contains an empty part, or use an
editing operation (Erase) to create an empty part.
Cannot Extract! When executing the Pattern Edit command Extract a
Rhythm Instrument (EXTRACT RHY) (p. 77), the
move-source part contained no data of the note num-
ber you specified by Extract Note.
Specify a note number for which data exists in the move-
source part.
Cannot Solo Sample
on the Song
You can’t perform solo sampling or solo with effect
sampling in Song mode.
Choose Patch mode or Pattern mode.
Card Not Ready! A CompactFlash card is not inserted in the slot. Insert a CompactFlash card into the slot.
Data Protected! The group in which you’re attempting to save the data
is protected.
You can’t save patches or rhythms in a protected bank. Either
change the save-destination bank, or alter the System settings
to switch off the protect setting for that bank (p. 126).
DIMM Error The DIMM is not inserted correctly. Turn off the power, and reinsert it correctly (p. 140).
Empty Pattern! The pattern cannot be played since it contains no per-
formance data.
Select a pattern that contains data.
Empty Sample! The sample contains no data. Select a sample that contains data.
Empty Song! The song has not been recorded, and therefore cannot
be played.
Select a song that contains data.
Illegal File! The MC-808 cannot use this file. The MC-808 can use only audio files (WAV/AIFF format).
Memory Damaged! The contents of memory may have been damaged. Please perform the Factory Reset operation (p. 25). If this does
not resolve the problem, please contact your dealer or the
nearest Roland Service Center.
MIDI Offline! There is a problem with the MIDI cable connection. Check that the MIDI cable has not been disconnected or bro-
ken.
No More Sample
Numbers!
The sample cannot be divided any further. Delete unneeded samples (p. 99) in order to allocate 256 or
more consecutive sample numbers.Since fewer than 256 consecutive sample numbers are
vacant, no further sampling is possible.
Now Playing! Since the MC-808 is playing, this operation cannot be
executed.
Stop playback before you execute the operation.
Pattern Full! Since the maximum number of notes that can be re-
corded in one pattern has been exceeded, no further
pattern recording is possible.
Erase unneeded data from the pattern you are recording (p.
81).
Permission Denied! The file is protected. —
Recording Overflow!
Too much recording data was received all at once and
could not be processed correctly.
Reduce the amount of data that’s being recorded.
Sample Memory
Full!
Since there is insufficient sample memory, no further
sampling or sample editing is possible.
Erase unneeded samples (p. 99).
Song Recording
Full!
Since the maximum number of patterns that can be re-
corded in one song has been exceeded, no further
song recording is possible.
A maximum of 50 patterns can be recorded in one song. No
further patterns can be recorded.
Sync Mode: Slave! If the system parameter “Sync Mode” is set to
“SLAVE,” you can’t perform pattern/song playback
(from the MC-808), solo sampling, or solo with effect
sampling.
Set “Sync Mode” to “MASTER” or “REMOTE“ (p. 119).
Unformatted! The CompactFlash card is in an unsupported format. Format the CompactFlash card (p. 125).
User/Card Memory
Full!
Saving is not possible because there is insufficient
space in the user memory or card memory.
Increase the amount of free memory by initializing patterns (p.
78) or songs (p. 109), or by deleting samples (p. 99).
Wrong Setting! The pattern edit setting is incorrect. Make the correct setting.
MC-808_r_e.book 142 ページ ２００７年７月１７日 火曜日 午後５時１分
To Next Page
Loading...
Need help?
General
