Cisco 2911 Configuration Guide

224
Cisco 3900 Series, Cisco 2900 Series, and Cisco 1900 Series Integrated Services Routers Generation 2 Software Configuration Guide
Chapter Upgrading the Cisco IOS Software
How to Upgrade the Cisco IOS Image
SUMMARY STEPS
1. enable
2. dir flash0:
3. From the displayed output of the dir flash0: command, compare the number of bytes available to
the minimum flash requirements for the new system image.
a. If the available memory is equal to or greater than the new system image’s minimum flash
requirements, proceed to the “Copying the System Image into Flash Memory” section on
page 226.
b. If the available memory is less than the new system image’s minimum flash requirements,
proceed to Step 4.
4. From the displayed output of the dir flash0: command, compare the number of bytes total to the
size of the system image to which you want to upgrade.
a. If the total memory is less than the new system image’s minimum flash requirements, you must
upgrade your compact flash memory card. See the hardware installation guide for your router.
b. If the total memory is equal to or greater than the new system image’s minimum flash
requirements, proceed to Step 5.
5. dir /all flash0:
6. From the displayed output of the dir /all flash0: command, write down the names and directory
locations of the files that you can delete.
7. (Optional) copy flash0: {tftp | rcp}
8. (Optional) Repeat Step 7 for each file that you identified in Step 6.
9. delete flash0:directory-path/filename
10. Repeat Step 9 for each file that you identified in Step 6.
11. dir flash0:[partition-number:]
12. From the displayed output of the dir flash0: command, compare the number of bytes available to
the size of the system image to which you want to upgrade.
a. If the available memory is less than the new system image’s minimum flash requirements, then
you must upgrade your compact flash memory card to a size that can accommodate both the
existing files and the new system image. See the hardware installation guide for your router.
b. If the available memory is equal to or greater than the new system image’s minimum flash
requirements, proceed to the “Copying the System Image into Flash Memory” section on
page 226.

Cisco 2911 Specifications

General

Ethernet LAN	Yes
Cabling technology	10/100/1000Base-T(X)
Networking standards	IEEE 802.1Q, IEEE 802.1ag, IEEE 802.3, IEEE 802.3ab, IEEE 802.3af, IEEE 802.3ah, IEEE 802.3u
Ethernet LAN data rates	10, 100, 1000 Mbit/s
Ethernet interface type	Gigabit Ethernet
DHCP client	-
Routing protocols	BGP, EIGRP, OSPF
Supported protocols	IPv4, IPv6, IS-IS, IGMPv3, PIM SM, SSM, DVMRP, IPSec, GRE, BVD, MPLS, L2TPv3, PPP, MLPPP, MLFR, HDLC, RS-232, RS-449, X.21, V.35, EIA-530, PPPoE, ATM
USB version	2.0
RS-232 ports	1
Expansion slots	4 x EHWIC 2 x DSP 1 x ISM
USB ports quantity	2
Ethernet LAN (RJ-45) ports	3
Firewall security	Cisco IOS
Input current	2.2 A
AC input voltage	100 - 240 V
Power source type	AC
AC input frequency	47 - 63 Hz
Power consumption (typical)	50 W
Product color	Black
Rack capacity	2U
Operating altitude	0 - 4000 m
Non-operating altitude	0 - 4570 m
Storage temperature (T-T)	-40 - 80 °C
Operating temperature (T-T)	0 - 40 °C
Storage relative humidity (H-H)	5 - 95 %
Operating relative humidity (H-H)	5 - 85 %
Safety	UL 60950-1, CAN/CSA C22.2 No. 60950-1, EN 60950-1, AS/NZS 60950-1, IEC 60950-1
Electromagnetic compatibility	47 CFR, ICES-003, EN55022, CISPR22, AS/NZS 3548, VCCI V-3, EN 300-386, EN 61000, EN 55024, CISPR 24EN50082-1

Weight and Dimensions

Depth	304.8 mm
Width	438.2 mm
Height	88.9 mm
Weight	8200 g