TIMER
OPERATION
Before using the
timer
function, be sure
that
the Remote Control Unit is set
to
the correct current time, see page
4.
( To Use
the
ON
timer
or
OFF
timer
1
Press
the
START / STOP button (Fig. 6 @).
(if
the
unit
is
already operating, proceed
to
step 2).
The
indoor
unit's OPERATION Indicator Lamp (red) (Fig. 3 @)
will
light.
2
Press
the
TIMER button (Fig. 6 ®)
to
select
the
OFF
timer
or
01\1
timer
operation.
Each
time
the button is pressed the timer function changes
in
the following
order:
C;RESET
.....
SLEEP-OFF-ON-----'l
PROGRAM
(OFF
--+
ON,
OFF
+-ON)----.J
The
indoor
unit's green TIMER lamp (Fig. 3 ®)
will
light.
3
Use
the
SET
TEMP./
SET TIME buttons (Fig. 6
@»)
to
adjust
the
desired
OFF
time
or
ON
time.
Set the
time
while the
time
display is flashing (the flashing
will
continue
for
about five seconds).
EB
button: Press
to
advance the time.
e button: Press
to
reverse the time.
About
five seconds later, the entire display
will
reappear.
[To
Cancel
the
TImer
Use the TIMER button to select "TIMER
RESET."
The air conditioner
will
return to normal
operation.
I
To
Change
the
TImer Settings
Perform steps 2 and 3.
To
Stop
Air
Conditioner Operation
while
the
TImer
is
Operating
Press the
START
f
STOP
button.
I
To
Change Operating Conditions
If
you
wish
to
change operating conditions
(Mode,
Fan
Speed, Thermostat Setting,
SUPER
QUIET mode), after making the
timer
setting
wait
until the entire display
reappears, then press the appropriate
buttons
to
change
the
operating condition
desired.
I
~~_o
__
U_s_e_t_h_e_P_r_o_g_ra_m
__
Tl_I_m_e_r
________________________
~J
1
Press
the
START / STOP button (Fig. 6
®».
(if
the
unit is already operating, proceed
to
step 2).
The
indoor
unit's OPERATION Indicator Lamp (red) (Fig. 3 @)
will
light.
2
Set
the
desired times for OFF
timer
and
ON
timer.
See
the
section liTo Use the ON TImer
or
OFF
TImer"
to
set the desired
mode
and times.
About
three seconds later, the entire display
will
reappear.
The
indoor
unit's
TIMER Indicator Lamp (green) (Fig. 3 ®)
will
light.
3
Press
the
TIMER button (Fig. 6
®»)
to
select
the
PROGRAM timer operation (OFF
-+
ON or
OFF
+-
ON
will display).
The display
will
alternately
show
"OFF
timer"
and
"ON
timer"
f then change
to
show
the
time
setting
for
the operation
to
occur first.
• The
program
timer
will
begin operation. (
If
the
ON
timer
has been
selected
to
operate first, the
unit
will
stop operating at this point).
About
five seconds later, the entire display
will
reappear.
About
the
Program Timer J
• The program
timer
allows you
to
integrate
OFF
timer
and
ON
timer
operations in
a single sequence. The sequence can involve one
transition
from
OFF
timer
to
ON timer,
or
from
ON
timer
to
OFF
timer,
within
a
twenty-four
hour
period.
• The first
timer
function to operate
will
be
the one set nearest
to
the current time.
The
order
of
operation is indicated
by
the
arrow
in
the
Remote Control
Unit's
Display
(OFF
--+ ON
or
OFF
+-
ON
).
• One
example
of
Program
timer
use
might
be
to
have
the
air
conditioner
automatically
stop (
OFF
timer)
after
you go
to
sleep, then start (
ON
timer)
automatically in the
morning
before you arise.
Use
the
TIMER button
to
select "TIMER
RESET."
The
air
conditioner
will
return
to
normal
operation.
I
To
Change
the
TImer
Settings
1.
Follow
the
instructions given in the
section
"To
Use
the
ON TImer
or
OFF
TImer" to select the
timer
setting you
wish
to
change.
2. Press the TIMER button
to
select either
OFF
--+ ON
or
OFF
+-
ON.
To
Stop
Air
Conditioner
Operation
while
the
TImer is Operating
Press the START / STOP button.
I
To
Change Operating Conditions
If
you
wish
to
change operating conditions
(Mode,
Fan
Speed, Thermostat Setting,
SUPER
QUIET mode), after making the
timer
setting
wait
until
the
entire display
reappears, then press the appropriate
buttons
to
change the operating condition
desired.
En-8
To Next Page
Loading...
Need help?
General
