Garmin GTR 200 User Manual

Name: Garmin GTR 200
Brand: Garmin
Rating: 5 (1 reviews)

85 pages

To Next Page

To Previous Page

GTR 200 Installation Manual 190-01553-00

Page A-2 Rev. B

Figure A-1 Shield Block Install onto a Backshell

Default Chapter7
- Table of Contents7
Paragraph Page8
Section 1 General Description13
Table13
Section 1 General Description13
- Introduction13
- Equipment Description13
- Table 1-1 Available Units13
- Technical Specifications14
- Table 1-2 Physical Characteristics14
- Table 1-3 General Specifications14
- Table 1-4 Display Specifications15
- Table 1-5 COM Transmitter Specifications15
- Table 1-6 COM Receiver Specifications16
- Certification17
- Reference Documents17
- Table 1-7 FCC Grant of Equipment Authorization17
- Table 1-8 Reference Documents17
Section 2 Installation Overview19
Section 2 Installation Overview19
- Introduction19
- Unit Configurations19
- Available Accessories19
- Table 2-1 Catalog Part Numbers19
- Table 2-2 Standard Kit Accessories19
- Installation Considerations20
- Antenna Considerations20
- Table 2-4 Optional Accessories20
- Mounting Considerations22
- Cabling and Wiring22
- Air Circulation and Cooling23
- Compass Safe Distance23
- Section 2 2-1 –24
Section 3 Installation Procedures25
Section 3 Installation Procedures25
- Unpacking the Unit25
- Wiring Harness Installation25
- Table 3-1 Recommended Crimp Tools (or Equivalent)25
- Table 3-2 Socket Contact Part Numbers25
- Backshell Assembly26
- Mounting Requirements26
- Antenna Installation and Connections27
Section 3 Installation Procedures28
- Post Installation Configuration and Checkout Procedures28
- Figure 3-1 GTR 200 Front Panel28
- Figure 3-2 Configuration Mode Home Page29
- Table 3-3 Configuration Default Settings30
- Figure 3-3 COM Setup Page31
- Table 3-4 COM Setup Page Selections31
- Figure 3-4 ICS Sidetone Selection32
- Figure 3-5 Audio Setup Page (AUX and Music Disabled)33
- Figure 3-6 Audio Setup Page (AUX and Music Enabled)33
- Table 3-5 Audio Setup Page Selections33
- Figure 3-7 Softkey Setup Page34
- Table 3-6 Softkey Setup Page Selections34
- Figure 3-8 Discrete Setup Page35
- Table 3-7 Discrete Setup Page Selections35
- Figure 3-9 Lighting Setup Page36
- Table 3-8 Lighting Setup Page Selections36
- Figure 3-10 Lighting Graph37
- Figure 3-11 RS-232 Status Page37
- Figure 3-12 Headset Tests Page38
- Figure 3-13 COM Tests Page39
- Figure 3-14 Audio Tests Page40
- Table 3-9 Audio Tests Source Selections40
- Table 3-10 Discrete Inputs41
- Table 3-11 TX Interlock Connections42
- Unit Software44
- Figure 3-15 about Page44
- Figure 3-16 Software Update Page44
- Figure 3-17 Micro SD Insertion45
- Figure 3-18 Software Update Page - Scanning Card45
- Section 3 3-1 –46
- Continued Airworthiness46
- Figure 3-19 Software Update Page - no Update Found46
- Figure 3-20 Software Update Page - Update Software46
- Figure 3-21 Software Update Page - Preparing Update46
- Figure 3-22 Software Update Page - Unit will Reboot46
Section 4 Connector Pinout Information47
Section 4 Connector Pinout Information47
Section 4 Connector Pinout Information47
- Pin Function List47
- Figure 4-1 J2001 Looking at Rear of Unit47
- Table 4-1 J2001 Connector47
- Power48
- Lighting Bus48
- Serial Data - RS-23249
- Aux Mono Audio49
- Headset Audio50
- Music Inputs50
- Receiver Audio50
- Pilot/Copilot PTT Inputs51
- TX Interlock51
- Discrete Inputs51
- Section 4 4-1 –52
Appendix A Shield Block Connector Installation Instructions53
Paragraph53
Appendix A Shield Block Connector Installation Instructions53
- Shield Block Installation Parts53
- Table A-1 Parts Not Supplied for a Shield Block Installation (Figure53
Appendix A Shield Block Connector Installation Instructions54
- Figure A-1 Shield Block Install Onto a Backshell54
- Figure A-2 Method A.1 for Shield Termination55
- Shield Termination Technique - Method A.1 (Standard55
- Table A-2 Shielded Cable Preparations for Garmin Connectors55
- Figure A-3 Insulation/Contact Clearance57
- Figure A-4 Method A.2 (Daisy Chain) for Shield Termination59
- Shield Termination - Method B.1 (Quick Term59
- Shield Termination Technique - Method A.2 (Daisy Chain59
- Figure A-5 Method B.1 (Quick Term) for Shield Termination60
- Figure A-6 Method B.2 (Daisy Chain-Quick Term) for Shield Termination61
- Shield Termination-Method B.2 (Daisy Chain-Quick Term61
- Table A-3 Shielded Cable Preparations - (Quick Term61
- Daisy Chain between Methods a and B62
- Figure A-7 Daisy Chain between Methods a and B62
- Splicing Signal Wires62
- Figure63
- Figure A-8 D-Sub Spliced Signal Wire Illustration63
Appendix B Serial Interface Specifications65
- Electrical Interface65
- Message Formats65
Appendix C Outline and Installation Drawings77
Appendix C Outline and Installation Drawings77
- Figure C-1 GTR 200 Outline Drawing77
Appendix C Outline and Installation Drawings78
- Figure C-2 GTR 200 Assembly Drawing78
- Figure C-3 GTR 200 Installation Drawing79
- Figure C-4 GTR 200 Panel Cutout Drawing80
Appendix D Interconnect Examples81
Appendix D Interconnect Examples81
- Figure D-1 GTR 200 Interconnect Example Notes81
- Figure D-2 GTR 200- Power & Ground/Intercom/Gdu 37X Interconnect Example82
- Figure D-3 GTR 200- Power & Ground/Gma 240/GNS 430/Aera 79X Interconnect Example83
- Figure D-4 GTR 200- Mono Audio/Remote Mount Jack Interconnect Example84
- Figure D-5 GTR 200- J2001 Connector Layout85

Other manuals for Garmin GTR 200

Pilot's Guide34 pages

Questions and Answers:

Need help?

Do you have a question about the Garmin GTR 200 and is the answer not in the manual?

Garmin GTR 200 Specifications

General

Modulation	AM
Operating Temperature	-20°C to +55°C
Channel Spacing	8.33 kHz / 25 kHz
Transmit Power	10 W
Operating Voltage	14/28 VDC systems
Frequency Range	118.000 - 136.975 MHz

Related product manuals

Garmin GTR 200B

88 pages

Garmin GTR 200 User Manual

Table of Contents

Other manuals for Garmin GTR 200

Questions and Answers:

Garmin GTR 200 Specifications

Related product manuals