Greensmaster 3150Hydraulic System Page 4 -- 52
Filtering Closed--Loop Traction Circuit
Filteringofaclosed--loop hydraulicsystemafteramajor
component failure (e.g. piston (traction) pump or wheel
motor) is a requirement to prevent debris from transmit-
ting throughout the system. If a closed --loop hydraulic
systemfilteringtoolisnotusedtoensuresystemcleanli-
ness, repeat failures, as well as subsequent damage to
other hydraulic components in the affected system, will
occur. To effectively remove contamination from
closed--looptractioncircuit,useofthe Torohighflowhy-
draulic filter and hydraulic hose kits are recommended
(see Special Tools in this chapter).
1. Parkmachineonalevelsurfacewithenginestopped
and key removed from ignition switch.
2. Raise machine so all driven wheels are off the
ground. Support raised machine with appropriate jack-
stands.
NOTE: If wheelmotorwasreplaced,installhighflowfil-
tertotheinletofnewmotorinsteadoftopiston(traction)
pump fitting. This will prevent system contamination
from entering and damaging the new motor.
3. Thoroughly clean junction of hydraulic hose and
lowerfittingonsideofpistonpump(Fig.35).Disconnect
hose from lower pump fitting.
4. Connect Toro high flow hydraulic filter in series be-
tweenlower pistonpumpfitting anddisconnectedhose.
Usehydraulichosekit(seeSpecialToolsinthischapter)
to connect filter to machine. Make sure that fitting and
hose connections are properly tightened.
IMPORTANT: Use only hydraulic fluids specified in
Traction Unit Operator’s Manual. Other fluids could
cause system damage.
5. After installing high flow filter to machine, check and
fillhydraulicreservoirwith newhydraulicoil asrequired.
6. Startengineandrun atidle speed. Checkfor anyhy-
draulic leakage from filter and hose connections. Cor-
rect any leaks before proceeding.
CAUTION
Alldrivenw heels willbeoffthegroundandrotat-
ing during this operation. Make sure machine is
wellsupportedsoitwillnotmoveandaccidental-
ly fall.
IMPORTANT: While engaging the traction circuit,
monitor the indicator on the high flow hydraulic fil-
ter. If the indicator should show red, either reduce
pressure on the traction pedal or reduce engine
speed to decrease hydraulic flow through the filter.
7. With engine running at low idle speed, slowly move
thetractionpedaltotheforward direction to allow flow
throughthetractioncircuitandhighflowfilter.Keeptrac-
tion circuit engaged for five (5) minutes while gradually
increasing both forward pressure on traction pedal and
engine speed. Monitor filter indicator to make sure that
green color is showing during operation.
IMPORTANT: If usinga filterthat is not the bi--direc-
tional Toro high flow filter, do not press the traction
pedal in the reverse direction. If flow is reversed
when using a filter that is not bi--directional, debris
from the filter will re--enter the traction circuit.
8. With engine running at high idle speed, alternately
movetractionpedalfromforwardtor everse.Whilemon-
itoring filter indicator, continue this process for an addi-
tional five (5) minutes.
9. Shut engine off andremove keyfrom ignitionswitch.
10.Remove highflow hydraulicfilter andhydraulic hose
kit from machine. Connect hydraulic hose to lower pis-
tonpumpfitting.Makesuretoproperlytightenhose(see
Hydraulic Hose and Tube Installation in the General In-
formation section of this chapter).
11.Lowermachinetoground.
12.Check oillevelinhydraulic reservoirandadd correct
oil if necessary.
1. Piston pump 2. Lower pump fitting
Figure 35
2
1
To Next Page
Loading...
Need help?
General
