Cisco Catalyst 2960-X User Manual

PurposeCommand or Action
Authenticates the CA by getting the public key of the CA. Use the
same name used in Step 5.
crypto ca authentication name
Example:
Switch(config)# crypto ca authentication
Step 11
your_trustpoint
Obtains the certificate from the specified CA trustpoint. This
command requests a signed certificate for each RSA key pair.
crypto ca enroll name
Example:
Switch(config)# crypto ca enroll
your_trustpoint
Step 12
Returns to privileged EXEC mode.end
Example:
Switch(config)# end
Step 13
Configuring the Secure HTTP Server
Beginning in privileged EXEC mode, follow these steps to configure a secure HTTP server:
Before You Begin
If you are using a certificate authority for certification, you should use the previous procedure to configure
the CA trustpoint on the switch before enabling the HTTP server. If you have not configured a CA trustpoint,
a self-signed certificate is generated the first time that you enable the secure HTTP server. After you have
configured the server, you can configure options (path, access list to apply, maximum number of connections,
or timeout policy) that apply to both standard and secure HTTP servers.
To verify the secure HTTP connection by using a Web browser, enter https://URL, where the URL is the IP
address or hostname of the server switch. If you configure a port other than the default port, you must also
specify the port number after the URL. For example:
AES256_SHA2 is not supported.Note
https://209.165.129:1026
or
https://host.domain.com:1026
Catalyst 2960-X Switch Security Configuration Guide, Cisco IOS Release 15.0(2)EX
OL-29048-01 131
Configuring Secure Socket Layer HTTP
Configuring the Secure HTTP Server

Cisco Catalyst 2960-X Specifications

General

Console port	RJ-45
USB 2.0 ports quantity	2
SFP module slots quantity	4
Installed SFP modules quantity	-
Gigabit Ethernet (copper) ports quantity	48
Basic switching RJ-45 Ethernet ports type	Gigabit Ethernet (10/100/1000)
Power source	AC
Input current	5 A
AC input voltage	100 - 240 V
Power consumption (typical)	60.9 W
Number of power supply units	1
Redundant power supply (RPS) support	Yes
Operating altitude	0 - 3000 m
Non-operating altitude	0 - 4000 m
Storage temperature (T-T)	-25 - 70 °C
Operating temperature (T-T)	-5 - 40 °C
Operating relative humidity (H-H)	10 - 95 %
Switching protocols	UDP, TCP, RADIUS/TACACS+
Number of VLANs	1023
Networking standards	IEEE 802.1ab, IEEE 802.1D, IEEE 802.1p, IEEE 802.1Q, IEEE 802.1s, IEEE 802.1w, IEEE 802.1x, IEEE 802.3, IEEE 802.3ab, IEEE 802.3ad, IEEE 802.3ae, IEEE 802.3af, IEEE 802.3ah, IEEE 802.3at, IEEE 802.3az, IEEE 802.3u, IEEE 802.3x, IEEE 802.3z
Throughput	107.1 Mpps
Jumbo frames	9216
Number of queues	8
MAC address table	16000 entries
Number of static routes	1000
DHCP features	DHCP server
Authentication	MAC-based authentication, Port-based authentication
Security algorithms	802.1x RADIUS, SNMP, SSH
Access Control List (ACL) rules	3
Switch type	Managed
Switch layer	L2/L3
Safety	UL 60950-1, CAN/CSA-C22.2 No. 60950-1, EN 60950-1, IEC 60950-1, AS/NZS 60950-1
Form factor	1U
Product color	Black
Total Power over Ethernet (PoE) budget	370 W
Power over Ethernet (PoE) ports quantity	24
Power over Ethernet plus (PoE+) ports quantity	12
Memory type	DRAM
Noise level	39 dB
Flash memory	128 MB
Internal memory	512 MB
Processor frequency	600 MHz
Mean time between failures (MTBF)	276870 h

Weight and Dimensions

Depth	368 mm
Width	445 mm
Height	45 mm
Weight	5800 g