Cisco Catalyst 2960-X User Manual

PurposeCommand or Action
Returns to privileged EXEC mode.end
Example:
Switch(config)# end
Step 6
Monitoring IPv4 ACLs
You can monitor IPv4 ACLs by displaying the ACLs that are configured on the switch, and displaying the
ACLs that have been applied to interfaces and VLANs.
When you use the ip access-group interface configuration command to apply ACLs to a Layer 2 or 3 interface,
you can display the access groups on the interface. You can also display the MAC ACLs applied to a Layer
2 interface. You can use the privileged EXEC commands as described in this table to display this information.
Table 18: Commands for Displaying Access Lists and Access Groups
PurposeCommand
Displays the contents of one or all current IP and MAC address
access lists or a specific access list (numbered or named).
show access-lists [number | name]
Displays the contents of all current IP access lists or a specific
IP access list (numbered or named).
show ip access-lists [number | name]
Displays detailed configuration and status of an interface. If IP
is enabled on the interface and ACLs have been applied by using
the ip access-group interface configuration command, the access
groups are included in the display.
show ip interface interface-id
Displays the contents of the configuration file for the switch or
the specified interface, including all configured MAC and IP
access lists and which access groups are applied to an interface.
show running-config [interface
interface-id]
Displays MAC access lists applied to all Layer 2 interfaces or
the specified
Layer 2 interface.
show mac access-group [interface
interface-id]
Catalyst 2960-X Switch Security Configuration Guide, Cisco IOS Release 15.0(2)EX
OL-29048-01 179
Configuring IPv4 ACLs
Monitoring IPv4 ACLs

Cisco Catalyst 2960-X Specifications

General

Console port	RJ-45
USB 2.0 ports quantity	2
SFP module slots quantity	4
Installed SFP modules quantity	-
Gigabit Ethernet (copper) ports quantity	48
Basic switching RJ-45 Ethernet ports type	Gigabit Ethernet (10/100/1000)
Power source	AC
Input current	5 A
AC input voltage	100 - 240 V
Power consumption (typical)	60.9 W
Number of power supply units	1
Redundant power supply (RPS) support	Yes
Operating altitude	0 - 3000 m
Non-operating altitude	0 - 4000 m
Storage temperature (T-T)	-25 - 70 °C
Operating temperature (T-T)	-5 - 40 °C
Operating relative humidity (H-H)	10 - 95 %
Switching protocols	UDP, TCP, RADIUS/TACACS+
Number of VLANs	1023
Networking standards	IEEE 802.1ab, IEEE 802.1D, IEEE 802.1p, IEEE 802.1Q, IEEE 802.1s, IEEE 802.1w, IEEE 802.1x, IEEE 802.3, IEEE 802.3ab, IEEE 802.3ad, IEEE 802.3ae, IEEE 802.3af, IEEE 802.3ah, IEEE 802.3at, IEEE 802.3az, IEEE 802.3u, IEEE 802.3x, IEEE 802.3z
Throughput	107.1 Mpps
Jumbo frames	9216
Number of queues	8
MAC address table	16000 entries
Number of static routes	1000
DHCP features	DHCP server
Authentication	MAC-based authentication, Port-based authentication
Security algorithms	802.1x RADIUS, SNMP, SSH
Access Control List (ACL) rules	3
Switch type	Managed
Switch layer	L2/L3
Safety	UL 60950-1, CAN/CSA-C22.2 No. 60950-1, EN 60950-1, IEC 60950-1, AS/NZS 60950-1
Form factor	1U
Product color	Black
Total Power over Ethernet (PoE) budget	370 W
Power over Ethernet (PoE) ports quantity	24
Power over Ethernet plus (PoE+) ports quantity	12
Memory type	DRAM
Noise level	39 dB
Flash memory	128 MB
Internal memory	512 MB
Processor frequency	600 MHz
Mean time between failures (MTBF)	276870 h

Weight and Dimensions

Depth	368 mm
Width	445 mm
Height	45 mm
Weight	5800 g