Cisco Catalyst 2960-X User Manual

The request is initiated from a CoA client (typically a AAA or policy server) and directed to the device that
acts as a listener.
The table below shows the RADIUS CoA commands and vendor-specific attributes (VSAs) supported by
Identity-Based Networking Services. All CoA commands must include the session identifier between the
device and the CoA client.
Table 7: RADIUS CoA Commands Supported by Identity-Based Networking Services
Cisco VSACoA Command
Cisco:Avpair=“subscriber:command=activate-service”
Cisco:Avpair=“subscriber:service-name=<service-name>”
Cisco:Avpair=“subscriber:precedence=<precedence-number>”
Cisco:Avpair=“subscriber:activation-mode=replace-all”
Activate service
Cisco:Avpair=“subscriber:command=deactivate-service”
Cisco:Avpair=“subscriber:service-name=<service-name>”
Deactivate service
Cisco:Avpair=“subscriber:command=bounce-host-port”
Bounce host port
Cisco:Avpair=“subscriber:command=disable-host-port”
Disable host port
Cisco:Avpair=“subscriber:command=session-query”
Session query
Cisco:Avpair=“subscriber:command=reauthenticate”
Cisco:Avpair=“subscriber:reauthenticate-type=last” or
Cisco:Avpair=“subscriber:reauthenticate-type=rerun”
Session reauthenticate
This is a standard disconnect request and does not require a VSA.Session terminate
Cisco:AVpair="interface-template-name=<interfacetemplate>"
Interface template
Change-of-Authorization Requests
Change of Authorization (CoA) requests, as described in RFC 5176, are used in a push model to allow for
session identification, host reauthentication, and session termination. The model is comprised of one request
(CoA-Request) and two possible response codes:
•
CoA acknowledgment (ACK) [CoA-ACK]
•
CoA non-acknowledgment (NAK) [CoA-NAK]
The request is initiated from a CoA client (typically a RADIUS or policy server) and directed to the switch
that acts as a listener.
Catalyst 2960-X Switch Security Configuration Guide, Cisco IOS Release 15.0(2)EX
62 OL-29048-01
Configuring RADIUS
RADIUS Change of Authorization

Cisco Catalyst 2960-X Specifications

General

Console port	RJ-45
USB 2.0 ports quantity	2
SFP module slots quantity	4
Installed SFP modules quantity	-
Gigabit Ethernet (copper) ports quantity	48
Basic switching RJ-45 Ethernet ports type	Gigabit Ethernet (10/100/1000)
Power source	AC
Input current	5 A
AC input voltage	100 - 240 V
Power consumption (typical)	60.9 W
Number of power supply units	1
Redundant power supply (RPS) support	Yes
Operating altitude	0 - 3000 m
Non-operating altitude	0 - 4000 m
Storage temperature (T-T)	-25 - 70 °C
Operating temperature (T-T)	-5 - 40 °C
Operating relative humidity (H-H)	10 - 95 %
Switching protocols	UDP, TCP, RADIUS/TACACS+
Number of VLANs	1023
Networking standards	IEEE 802.1ab, IEEE 802.1D, IEEE 802.1p, IEEE 802.1Q, IEEE 802.1s, IEEE 802.1w, IEEE 802.1x, IEEE 802.3, IEEE 802.3ab, IEEE 802.3ad, IEEE 802.3ae, IEEE 802.3af, IEEE 802.3ah, IEEE 802.3at, IEEE 802.3az, IEEE 802.3u, IEEE 802.3x, IEEE 802.3z
Throughput	107.1 Mpps
Jumbo frames	9216
Number of queues	8
MAC address table	16000 entries
Number of static routes	1000
DHCP features	DHCP server
Authentication	MAC-based authentication, Port-based authentication
Security algorithms	802.1x RADIUS, SNMP, SSH
Access Control List (ACL) rules	3
Switch type	Managed
Switch layer	L2/L3
Safety	UL 60950-1, CAN/CSA-C22.2 No. 60950-1, EN 60950-1, IEC 60950-1, AS/NZS 60950-1
Form factor	1U
Product color	Black
Total Power over Ethernet (PoE) budget	370 W
Power over Ethernet (PoE) ports quantity	24
Power over Ethernet plus (PoE+) ports quantity	12
Memory type	DRAM
Noise level	39 dB
Flash memory	128 MB
Internal memory	512 MB
Processor frequency	600 MHz
Mean time between failures (MTBF)	276870 h

Weight and Dimensions

Depth	368 mm
Width	445 mm
Height	45 mm
Weight	5800 g