KEB COMBIVERT F4-C Applications Manual

1 1
Name:Basis
KEB COMBIVERT F4-C
10
05.01.99
Introduction
General
© KEB Antriebstechnik, 1997
All Rights reserved
Chapter Section Page
Date
6.7 Keep on Running Functions..............................................................6.7.3
6.7.1 Ramp Stop and Hardware Current Limit .............................6.7.3
6.7.2 Maximum Constant Current (Stall-function) ........................6.7.5
6.7.3 Automatic Restart and Speed Search .................................6.7.7
6.7.4 Electronic Motor Protection .................................................6.7.9
6.7.5 Dead Time Compensation (uF.17)....................................6.7.11
6.7.6 Base-Block Time ...............................................................6.7.11
6.8 Parameter Sets ...................................................................................6.8.3
6.8.1 Non-programmable Parameters ..........................................6.8.3
6.8.2 Copying of Parameter Sets (Fr.0, Fr.1, Fr.9) ........................6.8.3
6.8.3 Selection of Parameter Sets................................................6.8.4
6.8.4 Locking of Parameter Sets ..................................................6.8.6
6.8.5 Parameter Set ON and OFF Delay (Fr.5, Fr.6) ....................6.8.7
6.8.6 Used Parameters ................................................................6.8.7
6.9 Special Functions ..............................................................................6.9.3
6.9.1 DC-Brake.............................................................................6.9.3
6.9.2 Energy Saving Function ......................................................6.9.5
6.9.3 Power-Off Function..............................................................6.9.7
6.9.4 Motor Potentiometer Function ...........................................6.9.13
6.9.5 Timer Programming...........................................................6.9.17
6.9.6 Braking Control..................................................................6.9.19
6.9.7 Unit Conversion.................................................................6.9.23
6.10 Encoder Interface .............................................................................6.10.3
6.10.1 Encoder Summary ............................................................6.10.3
6.10.2 Encoder Interface with 2nd Encoder .................................6.10.4
6.10.3 Encoder Interface with Tacho Generator evaluation ..........6.10.6
6.10.4 Encoder Interface with ±10V Input ....................................6.10.6
6.10.5 Encoder Interface with Initiator Input .................................6.10.6
6.10.6 Speed Measurement .........................................................6.10.7
6.10.7 Evaluation of Incremental Encoders..................................6.10.8
6.10.8 Evaluation of Tacho Generators ........................................6.10.9
6.10.9 Evaluation of Initiators .....................................................6.10.10
6.10.10 Gearbox Factors .............................................................6.10.10
6.10.11 Error Message E.co1/E.co2 ............................................6.10.10
6.10.12 Definition of Actual Value Channel (cn.3)........................6.10.10
6.10.13 Frequent Errors ...............................................................6.10.11
6.10.14 Used Parameters ...........................................................6.10.11
6.11 PI-Controller......................................................................................6.11.3
6.11.1 The PI-Controller ...............................................................6.11.3
6.11.2 Controller Selection (cn.0).................................................6.11.4
6.11.3 Autoboost and Slip Compensation ....................................6.11.6
6.11.4 Set Value Calculation % ....................................................6.11.7
6.11.5 Actual Value Calculation %................................................6.11.9
6.11.6 Diameter Compensation..................................................6.11.10
6.11.7 Controller Action and Limiting .........................................6.11.11
6.11.8 Used Parameters ...........................................................6.11.12

KEB COMBIVERT F4-C Specifications

General

Brand	KEB
Model	COMBIVERT F4-C
Category	DC Drives
Language	English