Keithley 2635 Reference Manual

2600S-901-01 Rev. C / January 2008 I-1
Index
A
Accessories ..............................................1-4
Attributes ......................................12-3, 12-8
Auto ohms measurements .....................4-12
Auto range ................................................6-3
Auto zero ..................................................4-6
Front panel .......................................4-7
Front panel operation .......................4-7
NPLC caching ..................................4-6
Remote command ............................4-7
Remote operation .............................4-7
B
Baud rate ................................................11-9
Beeper ....................................................1-15
Branching ...............................................2-50
Buffer
Commands .......................................7-4
Configuration ....................................7-2
Dynamically allocated ......................7-8
Front panel .......................................7-2
Location number ..............................7-3
Overview ..........................................7-2
Programming examples ...................7-9
Reading attributes ............................7-6
Readings ..........................................7-4
Remote .............................................7-4
Status ...............................................7-8
Storage attributes .............................7-5
Timestamp .......................................7-3
C
Calibration
Commands .....................................16-7
Considerations ...............................16-2
Cycle ..............................................16-3
Errors .............................................16-5
Procedure .......................................16-8
Recommended equipment .............16-3
Steps ..............................................16-5
Capabilities ...............................................1-2
Source-measure ...............................4-2
Chassis ground ................... 1-10, 1-12, 3-3
Chunk .......................................................2-6
Circuit configurations ......................4-5, 8-16
Basic ................................................4-5
Contact check ................................8-18
Measure only (V or I) ......................8-17
Source I ..........................................8-16
Source V ........................................8-17
Command programming .........................12-2
Attributes .............................. 12-3, 12-8
Conventions ................................... 12-2
Functions ............................. 12-3, 12-8
Logical instruments ........................ 12-5
Reading buffers ............................. 12-5
Syntax rules ................................... 12-4
Time and date values .................... 12-7
TSP-Link nodes ............................. 12-4
Commands
Requesting settings ....................... 1-24
Common commands ....................... C-2, E-7
*IDN? ...............................................C-3
*OPC ................................................C-3
*OPC? ..............................................C-3
*RST ................................................C-4
*TRG ................................................C-4
*TST? ...............................................C-4
*WAI .................................................C-4
Summary .........................................C-2
Compliance
Limit ......................................... 4-3, 8-2
Maximum ......................................... 8-2
Principles ......................................... 8-3
Setting front panel compliance limit . 4-4
Setting remote compliance limit ....... 4-5
Compliance limit
Front panel operation ....................... 4-4
Remote operation ............................ 4-5
Setting .............................................. 4-4
Concatenation ........................................ 2-49
Connection
GPIB .............................................. 11-2
Connectors
Digital I/O ............................. 1-10, 1-12
IEEE-488 ............................. 1-10, 1-12
Output .................................. 1-10, 1-12
Power module ...................... 1-10, 1-12
RS-232 ................................. 1-10, 1-12
TSP-Link .............................. 1-10, 1-12
Contact check
Circuit configuration ....................... 8-18
Commands .................................... 4-18
Connections ..................................... 3-8
Measurements ............................... 4-17
Overview ........................................ 4-17
Programming example ................... 4-19
Contact information .................................. 1-3
Continuous power operating boundaries . 8-8
Cooling vents ......................................... 1-13
Coordinating overlapped operations,
(Remote Groups Only) ........................... 9-11
Copyting Test Scripts ............................. 9-12

Keithley 2635 Specifications

General

Brand	Keithley
Model	2635
Category	Measuring Instruments
Language	English