NETGEAR GS716T User Manual

104
GS716T and GS724T Gigabit Smart Switches
To configure CST port settings:
1. To configure CST settings for a physical port, click PORTS.
2. To configure CST settings for a Link Aggregation Group (LAG), click LAGS.
3. To configure CST settings for both physical ports and LAGs, click ALL.
4. Select the check box next to the port or LAG to configure. You can select multiple ports and
LAGs to apply the same setting to the selected interfaces. Select the check box in the
heading row to apply the same settings to all interfaces.
5. Configure the CST values for the selected port(s) or LAG(s):
• STP Status. Enable or disable the Spanning Tree Protocol Administrative Mode
associated with the port or port channel.
• Fast Link. Specifies if the specified port is an Edge Port with the CST. Possible
values are Enable or Disable. The default is Disable.
• Port State. The Forwarding state of this port. This field is read-only.
• Path Cost. Set the Path Cost to a new value for the specified port in the common and
internal spanning tree. It takes a value in the range of 1–200000000.
• Priority. The priority for a particular port within the CST. The port priority is set in
multiples of 16. If you specify a value that is not a multiple of 16, the priority is set to
the priority is automatically set to the next lowest priority that is a multiple of 16. For
example, if you set a value between 0 and 15, the priority is set to 0. If you specify a
number between 16 and 31, the priority is set to 16.
• External Port Path Cost. Set the External Path Cost to a new value for the specified
port in the spanning tree. It takes a value in the range of 1–200000000.
• Port ID. The port identifier for the specified port within the CST. It is made up from the
port priority and the interface number of the port.
• Hello Timer. Specifies the switch Hello time, which indicates the amount of time in
seconds a port waits between configuration messages. The value is fixed at 2
seconds.
6. Click Cancel to cancel the configuration on the screen and reset the data on the screen to
the latest value of the switch.
7. If you make any configuration changes, click Apply to send the updated configuration to the
switch. Configuration changes take place immediately.
8. Click Refresh to update the information on the screen with the most current data.

NETGEAR GS716T Specifications

General

Switch type	Managed
Switch layer	L3
Quality of Service (QoS) support	Yes
Stackable	-
Certification	CE, FCC, VCCI, EN, C-Tick, CCC, CSA, UL/cUL, IEC
Product color	Blue
LED indicators	Activity, Link, Power
SFP module slots quantity	2
Basic switching RJ-45 Ethernet ports type	Gigabit Ethernet (10/100/1000)
Basic switching RJ-45 Ethernet ports quantity	16
Number of VLANs	256
Networking standards	IEEE 802.1D, IEEE 802.1as, IEEE 802.1s, IEEE 802.1v, IEEE 802.3, IEEE 802.3ab, IEEE 802.3ad, IEEE 802.3i, IEEE 802.3u, IEEE 802.3x, IEEE 802.3z
Copper ethernet cabling technology	10BASE-T, 100BASE-TX, 100BASE-T, 1000BASE-T
Noise level	0 dB
Mean time between failures (MTBF)	567680 h
DHCP features	DHCP client
Security algorithms	802.1x RADIUS, HTTPS, SSL/TLS
AC input voltage	100 - 240 V
AC input frequency	50 - 60 Hz
Power consumption (typical)	14.4 W
MAC address table	16000 entries
Number of static routes	32
Operating altitude	0 - 3000 m
Storage temperature (T-T)	-20 - 70 °C
Operating temperature (T-T)	0 - 50 °C
Storage relative humidity (H-H)	0 - 95 %
Operating relative humidity (H-H)	0 - 90 %
Cables included	AC
Supported network protocols	IP

Weight and Dimensions

Depth	204 mm
Width	440 mm
Height	43 mm
Weight	2570 g