NETGEAR GS716T User Manual

193
GS716T and GS724T Gigabit Smart Switches
• Source IP Address. Specify the IP Address of the client originating the management
traffic.
• Mask. Specify the subnet mask associated with the IP address. The subnet mask is a
standard subnet mask, and not an inverse (wildcard) mask that you use with IP ACLs.
• Priority. Configure priority to the rule. The rules are validated against the incoming
management request in the ascending order of their priorities. If a rule matches,
action is performed and subsequent rules below are ignored. For example, if a
Source IP 10.10.10.10 is configured with priority 1 to permit, and Source IP
10.10.10.10 is configured with priority 2 to Deny, then access is permitted if the profile
is active, and the second rule is ignored.
2. To modify an access rule, select the check box next to the Rule Type, update the desired
settings, and click Apply
3. To delete an access rule, select the check box next to the Rule Type, and click Delete.
4. Click Cancel to cancel the configuration on the screen and reset the data on the screen to
the latest value of the switch.
Port Authentication
In port-based authentication mode, when 802.1X is enabled globally and on the port,
successful authentication of any one supplicant attached to the port results in all users being
able to use the port without restrictions. At any given time, only one supplicant is allowed to
attempt authentication on a port in this mode. Ports in this mode are under bidirectional
control. This is the default authentication mode.
The 802.1X network has three components:
• Authenticators: Specifies the port that is authenticated before permitting system access.
• Supplicants: Specifies the host connected to the authenticated port requesting access to
the system services.
• Authentication Server: Specifies the external server, for example, the RADIUS server
that performs the authentication on behalf of the authenticator, and indicates whether the
user is authorized to access system services.
From the Port Authentication link, you can access the following pages:
• Basic:
• 802.1X Configuration on page 194
• Advanced:
• Port Authentication on page 195
• Port Summary on page 198

NETGEAR GS716T Specifications

General

Switch type	Managed
Switch layer	L3
Quality of Service (QoS) support	Yes
Stackable	-
Certification	CE, FCC, VCCI, EN, C-Tick, CCC, CSA, UL/cUL, IEC
Product color	Blue
LED indicators	Activity, Link, Power
SFP module slots quantity	2
Basic switching RJ-45 Ethernet ports type	Gigabit Ethernet (10/100/1000)
Basic switching RJ-45 Ethernet ports quantity	16
Number of VLANs	256
Networking standards	IEEE 802.1D, IEEE 802.1as, IEEE 802.1s, IEEE 802.1v, IEEE 802.3, IEEE 802.3ab, IEEE 802.3ad, IEEE 802.3i, IEEE 802.3u, IEEE 802.3x, IEEE 802.3z
Copper ethernet cabling technology	10BASE-T, 100BASE-TX, 100BASE-T, 1000BASE-T
Noise level	0 dB
Mean time between failures (MTBF)	567680 h
DHCP features	DHCP client
Security algorithms	802.1x RADIUS, HTTPS, SSL/TLS
AC input voltage	100 - 240 V
AC input frequency	50 - 60 Hz
Power consumption (typical)	14.4 W
MAC address table	16000 entries
Number of static routes	32
Operating altitude	0 - 3000 m
Storage temperature (T-T)	-20 - 70 °C
Operating temperature (T-T)	0 - 50 °C
Storage relative humidity (H-H)	0 - 95 %
Operating relative humidity (H-H)	0 - 90 %
Cables included	AC
Supported network protocols	IP

Weight and Dimensions

Depth	204 mm
Width	440 mm
Height	43 mm
Weight	2570 g