NETGEAR GS716T User Manual

81
GS716T and GS724T Gigabit Smart Switches
4. Select the check box next to the port or LAG to configure. You can select multiple ports and
LAGs to apply the same setting to the selected interfaces. Select the check box in the
heading row to apply the same settings to all interfaces.
5. Configure or view the settings:
• Description. Enter the description string to be attached to a port. The string can be
up to 64 characters in length.
• Port Type. For most ports this field is blank. Otherwise, the possible values are:
• Probe: Indicates that the port is a monitoring (destination) port. For additional
information about port monitoring see
Port Mirroring on page 250.
• Mirrored: The port is a source port and mirrors traffic to the probe port. For
additional information about port monitoring see
Port Mirroring on page 250.
• LAG: Indicates that the port is a member of a Link Aggregation trunk. For more
information see
Link Aggregation Groups on page 83.
• Admin Mode. Use the menu to select the port control administration state, which can
be one of the following:
• Enable: The port can participate in the network (default).
• Disable: The port is administratively down and does not participate in the network.
• Port Speed. Use the menu to select the port’s speed and duplex mode. If you select
Auto, the duplex mode and speed will be set by the auto-negotiation process. The
port’s maximum capability (full duplex and 1000 Mbps) will be advertised. Otherwise,
your selection will determine the port’s duplex mode and transmission rate. The
factory default is Auto.
• Physical Status. Indicates the physical port’s speed and duplex mode
• Link Status. Indicates whether the Link is up or down.
• Link Trap. This object determines whether or not to send a trap when link status
changes. The factory default is Enable.
• Enable: Specifies that the system sends a trap when the link status changes.
• Disable: Specifies that the system does not send a trap when the link status
changes.
• Maximum Frame Size. Specifies the maximum Ethernet frame size the interface
supports. The size includes the Ethernet header, CRC, and payload. Any change to
the maximum frame size is immediately applied to all interfaces.
• MAC Address. Displays the physical address of the specified interface.
• PortList Bit Offset. Displays the bit offset value which corresponds to the port when
the MIB object type PortList is used to manage in SNMP.
• ifIndex. The ifIndex of the interface table entry associated with this port. If the
interface field is set to All, this field is blank.
6. Click Cancel to cancel the configuration on the screen and reset the data on the screen to
the latest value of the switch.
7. If you make any changes to the page, click Apply to apply the changes to the system.

NETGEAR GS716T Specifications

General

Switch type	Managed
Switch layer	L3
Quality of Service (QoS) support	Yes
Stackable	-
Certification	CE, FCC, VCCI, EN, C-Tick, CCC, CSA, UL/cUL, IEC
Product color	Blue
LED indicators	Activity, Link, Power
SFP module slots quantity	2
Basic switching RJ-45 Ethernet ports type	Gigabit Ethernet (10/100/1000)
Basic switching RJ-45 Ethernet ports quantity	16
Number of VLANs	256
Networking standards	IEEE 802.1D, IEEE 802.1as, IEEE 802.1s, IEEE 802.1v, IEEE 802.3, IEEE 802.3ab, IEEE 802.3ad, IEEE 802.3i, IEEE 802.3u, IEEE 802.3x, IEEE 802.3z
Copper ethernet cabling technology	10BASE-T, 100BASE-TX, 100BASE-T, 1000BASE-T
Noise level	0 dB
Mean time between failures (MTBF)	567680 h
DHCP features	DHCP client
Security algorithms	802.1x RADIUS, HTTPS, SSL/TLS
AC input voltage	100 - 240 V
AC input frequency	50 - 60 Hz
Power consumption (typical)	14.4 W
MAC address table	16000 entries
Number of static routes	32
Operating altitude	0 - 3000 m
Storage temperature (T-T)	-20 - 70 °C
Operating temperature (T-T)	0 - 50 °C
Storage relative humidity (H-H)	0 - 95 %
Operating relative humidity (H-H)	0 - 90 %
Cables included	AC
Supported network protocols	IP

Weight and Dimensions

Depth	204 mm
Width	440 mm
Height	43 mm
Weight	2570 g