Nikon T-RCP User Manual

I Preparations
2 Setting Attachment Information
- 16 -
5
Move to the next address of the revolving nosepiece using
the S key or the T key. Repeat steps 2 and 3 above.
ＯＢＪＥＣＴＩＶＥ
Ｓｅｒｉｅｓ Ｍａｇ． Ｅｓｃ．
１［Ｐ Ｆｌｕｏｒ ］［ＤＬ ４ｘ］[―]
２［
――――――――――］［―――――――――――――――］[－]
３［――――――――――］［―――――――――――――――］[－]
４［――――――――――］［―――――――――――――――］[－]
５［――――――――――］［―――――――――――――――］[－]
６［――――――――――］［―――――――――――――――］[－]
Ｅｄｉｔ
Ｔｙｐｅ Ｎ．Ａ． Ｗ．Ｄ．
―――――――――― ――――― ―――――
6
Press the MODE key to end the setting and to return to the
OPERATION screen.
Note:
If the revolving nosepiece is not connected, you cannot set the information on objectives.
“---------” indicates that no objective is attached or registered at the address.
If an attached objective is not listed among the presets, register it to the list of optional objectives.
For details, see V-7 (2) Objective in section V-7 (Registering Data for Optical Members).
(2) Condenser Module
Set the information on condenser modules attached to the condenser module changeover (motorized condenser
turret).
1
Press the MODE key, and the SETTING MENU screen will
appear on the LCD.
Select “Condenser” using the S key or the T key and
then press the [

] key.
ＳＥＴＴＩＮＧ ＭＥＮＵ
Ｏｂｊｅｃｔｉｖｅ
Ｃｏｎｄｅｎｓｅｒ
Ｆｉｌｔｅｒ
Ｅｘｃｉｔｅｒ
Ｂａｒｒｉｅｒ
Ｃｏｍｂｉｎａｔｉｏｎ（Ｏｂｊ．＞Ｃｏｎｄｅｎｓｅｒ）
Ｃｏｍｂｉｎａｔｉｏｎ（Ｆｉｌｔｅｒ＞ＥＸ／ＢＡ）
Ｍｏｒｅ
2
Select “Name” for the condenser module using the PREV
or NEXT key.
If the condenser module is marked “A,” select “BF.”
Note:
The numbers at the left of the screen represent the
addresses of the condenser module changeover.
ＣＯＮＤＥＮＳＥＲ
Ｎａｍｅ
１［
ＢＦ ］
２［――――――――――］
３［――――――――――］
４［――――――――――］
５［――――――――――］
Ｅｄｉｔ
3
Move to the next address of the condenser module
changeover using the S key or the T key. Repeat step
2 above.
ＣＯＮＤＥＮＳＥＲ
Ｎａｍｅ
１［ＢＦ ］
２［
――――――――――］
３［――――――――――］
４［――――――――――］
５［――――――――――］
Ｅｄｉｔ
4
Press the MODE key to end the setting and to return to the
OPERATION screen.
Note:
If the condenser module changeover is not connected, you cannot set the information on condenser modules.
“---------” indicates that no condenser module is attached or registered at the address.
If an attached condenser module is not listed in the presets, register it to the list of optional condenser modules.
For details, see V-7 (2) Condenser Module in section V-7 (Registering Data for Optical Members).

Nikon T-RCP Specifications

General

Brand	Nikon
Model	T-RCP
Category	Remote Control
Language	English