1. Safety
Product article number
Product serial number
Dealer
1.2 Important safety instructions
To prevent the risk of electrical shock
• This projector should be operated from an A C power source. Ensure that the mains voltage and capacity matches the p rojector
electrical ratings. If you are unable to install the AC requirements, contact your electrician. Do not defeat the purp ose of the
grounding.
• Installation according t o the local e lectrical c ode and regulations by qualified technical personnel o nly.
• This product is equipped with a three-terminal barrier strip for the connection of a m ono p ha
se line with a separate earth ground
PE. If you are unable to install the A C Requirements, contact your electrician. Do not defeat the purpose of the grounding.
• The cross-sectional area of the conductors in the power supply cord shall be not less than 4 mm
2
or AWG 10.
• The electronics o f the projector must be pow ered either from a suitable UPS unit or from the power outlet socket (UP S OUTLE T)
provided on the projector. For that reason an adapted sho rt power cord (2-pole 3-wire grounding) is added to the projector
accessories to loop through the power.
• The provided power output socket (UPS OUTLE T) on the projector may only be used to provide power to the projector elec-
tronics. Never connect other devices to this power output s ocket.
• The circuit breaker(s) that must be provided in the power circuit(s) of the projector is considered as general disconnect switch(es)
to s witch off the complete installation.
• Switch off the p rojector and unplug the power cord from the UPS INLET for removal of all pow er from the projector.
• Warning: High leakage current. Earth connection e ssential before connecting supply.
• Do not allow anything to rest on the power cord. Do not locate this projector where persons will walk on the cord.
• Do no t op erate the projector with a damaged cord or if the projector has b een dropped or damaged - until it has been exam ined
and approved for operation by a qualified service technician.
• Position the cord so that it will not be tripped over, pulled, or contact hot surfaces.
• If an extension cord is nec essary, a cord with a current rating at least equal to that of the projector should be used. A cord rated
for less amperage than the projector may overh eat.
• Never pus h objects of any kind into this projector through cabinet slots as they m ay touch dangerous voltage points or short
circuit parts that could result in a risk of fire or electrical shock.
• Do n ot expose this projector to rain or mois ture.
• Do not immerse or expose this projector in w ater or other liquids.
• Do not spill liquid of any kind on this projector.
• Should any liquid or solid object fall into the cabinet, unp lug the set and have it checked by qualified service personnel before
resuming operations.
• Do not d isassemble this projector, alway s take it to an authorized trained service person when service or repair work is required.
• Do not use an accessory attachment which is not recommended by the m anufacturer.
• Lightning - For added protection for this video product during a lightning storm, or when it is left unattended and unused for
long periods of time, unplug it from the w all outlet a nd disco nnect med ia and communication cables. This will pr event dam age
to the projec tor d ue to lightning and AC power-line surges.
To prevent personal injury
• Isolate electrically before replacing the lamp or lamp house. Caution: Hot lamp (house).
• Caution: High pressure lam p may explode if impro perly handled. Refer servicing to qualified se rvice per sonnel.
• To prevent injury and physical dam age, always read this manual and all labels on the system before inserting the lamp casing,
connecting to the wall outlet or adjusting the projector.
• To prevent injury, take note of the weight of the projector. Minimum 4 per sons are needed to carry the projector.
• To prevent injury, ensure that the lens , exhausting s ys
tem and all cover plates are correctly installed. See installation proce-
dures.
• Warning: high intensity light beam. NEV ER look into the lens ! High luminance could result in damage to the eye.
• Warning: extremely high brightness lamp s: This pr ojector uses extremely high brightness lamp s. Never attempt to look
directly into the lens or at the lamp. If the projection distance is less than 6 meter, any person needs to be at least 4 meters
away from the projected image. Avoid close range reflection of the projected image on any reflecting s urface ( such as glass,
metal, … ) . W hen ope rating the projector, we strongly recommend wearing suitable safety g lasses.
4
R5905050 DP2K C-SERIES 10/07/2012
To Next Page
Loading...
Need help?
General