1-68
Cisco IOS XR Troubleshooting Guide for the Cisco CRS-1 Router
OL-21483-02
Chapter 1 General Troubleshooting
Monitoring
TenGigE0/3/0/4 0/ 0% 0/ 0% 0/0 0/0
TenGigE0/3/0/5 0/ 0% 5342/ 0% 2.4M/0 166.8M/1743
TenGigE0/3/0/6 0/ 0% 0/ 0% 11.5T/0 11.5T/0
TenGigE0/3/0/7 852/ 0% 963/ 0% 379.7M/276 269.3M/312
TenGigE0/3/0/6.10 0/ 0% 0/ 0% 1.8T/0 1.8T/0
TenGigE0/3/0/6.20 0/ 0% 0/ 0% 1.8T/0 1.8T/0
TenGigE0/3/0/6.30 0/ 0% 0/ 0% 1.8T/0 1.8T/0
TenGigE0/3/0/6.40 0/ 0% 0/ 0% 1.8T/0 1.8T/0
TenGigE0/3/0/6.50 0/ 0% 0/ 0% 1.8T/0 1.8T/0
TenGigE0/3/0/6.60 0/ 0% 0/ 0% 1.8T/0 1.8T/0
TenGigE0/3/0/1.99 0/ 0% 0/ 0% 5040/0 4978/0
POS0/5/0/0 0/ 0% 0/ 0% 0/0 0/0
POS0/5/0/1 14658/ 0% 796/ 0% 611.8M/4764 657.5M/259
POS0/5/0/2 0/ 0% 0/ 0% 0/0 2.2M/0
POS0/5/0/3 0/ 0% 0/ 0% 0/0 70.0M/0
POS0/5/0/4 20346/ 0% 20033/ 0% 992.7M/6638 990.7M/6536
POS0/5/0/5 306/ 0% 306/ 0% 4.0M/100 4.0M/100
POS0/5/0/6 0/ 0% 0/ 0% 0/0 0/0
POS0/5/0/8 0/ 0% 0/ 0% 0/0 2.2M/0
POS0/5/0/10 729/ 0% 649/ 0% 97.8M/238 121.5M/212
POS0/5/0/11 723/ 0% 14187/ 0% 99.5M/238 648.7M/4664
POS0/5/0/12 0/ 0% 0/ 0% 0/0 0/0
Quit='q', Clear='c', Freeze='f', Thaw='t',
Next set='n', Prev set='p', Bytes='y', Packets='k'
monitor controller Command
Use the monitor controller command to monitor controller fabric or SONET counters in real-time. The
counters are refreshed every two seconds. The following example shows the output of the monitor
controller command.
RP/0/RP0/CPU0:router# monitor controller sonet 0/1/0/0
CRS-8_X1 Monitor Time: 00:00:00 SysUptime: 19:02:19
CRS-8_X1 Monitor Time: 00:00:02 SysUptime: 19:02:21
CRS-8_X1 Monitor Time: 00:00:04 SysUptime: 19:02:23
CRS-8_X1 Monitor Time: 00:00:06 SysUptime: 19:02:25
CRS-8_X1 Monitor Time: 00:00:08 SysUptime: 19:02:27
CRS-8_X1 Monitor Time: 00:00:10 SysUptime: 19:02:29
CRS-8_X1 Monitor Time: 00:00:12 SysUptime: 19:02:31
CRS-8_X1 Monitor Time: 00:00:14 SysUptime: 19:02:33
CRS-8_X1 Monitor Time: 00:00:16 SysUptime: 19:02:35
To Next Page
Loading...
Need help?
General
