To cancel searching for the AP:
Press _ while searching for the AP. A message will
appear. Then press < or • to select Yes and press _2).
EasySetupusingPIN (PersonalIdentification
Number)
1 From the PREFERENCES menu, highlight
Network Setup and press _,).
2 Press • or • to highlight Wireless Setup, and press
3 Press • or • to highlight Easy Setup, and press _).
4 Press < or • to select PIN.
5 Press • to highlight Start Scan, and press _°23.
6 Press • or • to select the desired AP and press _k).
Note: Check the MAC address on label of the AP or
the manual of it and select an AP.
7 When the PIN code window appears, enter the
displayed PIN into your AP, and then press (o_ to
start the PIN Setup. When a message displays to
report that the setup was successful, press ,,%
To cancel searching for the AP:
Press @ while searching for the AP. A message will
appear. Then press < or • to select Yes and press _}.
AssistedSetup
1 From the PREFERENCES menu, highlight
Network Setup and press _.
2 Press • o1"• to highlight Wireless Setup, and press
@.
3 Press • or • to highlight Assisted Setup, and press
@.
4 Press • or • to select the desired AP and press _,).
Note: Check the MAC address on label of the AP or
the manual of it and select an AP.
5 Highlight Security Key and press _. The Software
Keyboard window will appear.
6 Input the Security Key by using the Software
Keyboard (_#r' page 69). To save your setting, press
the BLUE button.
Note:
• The Security Key must adhere to these conditions:
-TKIP/AES: 8-63 ASCII or 64 Hex characters
-WEP: 5 or 13 ASCII or 10 or 26 Hex characters
• Key ID of WEP encryption to set is only one.
7 Highlight Done, and then press _,).
Note: If Network Name is not displayed, see step 4
and 5 in Manual Setup (_;; the next column) to set
Network Name before pressing Done.
Note: Settings are not saved if _ is pressed before Done
is selected.
ManualSetup
1 From the PREFERENCES menu, highlight
Network Setup and press .Fo_.
2 Press • or • to highlight Wireless Setup, and
press _.
3 Press • or • to highlight Manual Setup, and press
4 Press • or • to highlight Network Name, and
press _). The Software Keyboard window will
appear.
5 Input the Network Name by using the Software
Keyboard (_#r' page 69). To save your setting, press
the BLUE button.
6
7
8
9
Press • or • to highlight Authentication, and then
press < or • to select Open System, Shared Key,
WPA-PSK or WPA2-PSK
Press • or • to highlight Encryption, and then
press < or • to select None, WEP, TKIP or AES.
Note:
• Certain encryption types are only compatible with
specific authentication types.
- When Authentication is Open System, only WEP or
None is compatible.
- When Authentication is Shared Key, only WEP is
compatible.
- When Authentication is WPA-PSK or WPA2-PSK,
only TKIP or AES is compatible.
• When incompatible Authentication/Encryption
pairings are attempted, a warning message will be
displayed, and no connection attempt will be made
until the incompatibifity is resolved.
• Key ID of WEP encryption to set is only one.
Press • or • to highlight Security Key, and press
@. The Software Keyboard window ;viii appear.
Input the Security Key by using the Software
Keyboard (_vr page 69). To save your setting, press
the BLUE button.
Note: This item is grayed out when Encryption is
None.
10 Highlight Done, and then press @.
Note: When Encryption is None, a message will
appear. Press < or • to select Yes and press _o_.
Note: Settings are not saved if _ is pressed before Done
is selected.
66
To Next Page
Loading...
Need help?
General
Weight and Dimensions
