Wireless network problems
* Makesure the Dual BandWLANAdapter connection (_-_--_
page 22).
* Checkthat the power of AP is On.
* After starting wireless network setup, confirm that the
window that the wireless constitution was completed
successfully appears.
* Checkthe AP's connection status (_-_-_page 67).
* If the AP does not correspond to the PBCof WPS, Easy
Setup (PBC)cannot set even if its push-button is
pressed.
* If APlist is not displayed in EasySetup (PIN) or Assisted
Setup, the power of AP may be Off. Check that it is On,
and then try starting the AP scan.
* Readthe AP's instruction manual.
Media Player problems
* Makesure that devices are connected correctly.
* Incorrect behavior may occur with a USBHUB
connection.
* If the played photo is low-resolution, make sure that the
DMS may changethe scale of a image. This TV may
select and play the changed image.
* If this TV cannot play some photo files, make sure that
they were not edited by PC application. Some PC
applications may changethe photo format to
incompatible.
* If the played content is low-resolution, makesure that
the DMS supports the multiple formats for this content.
This TV may select one of the formats for the content
automatically.
* If this TVcannot play the content of DMS, makesure that
the content is not copy-protected.
* If a playback is unstable, check the traffic or congestion
on the network.
° Contents that PC originally recorded may not be able to
be played correctly.
° A DMS may restrict accessfrom this TV to the DMS.See
the DMS's manual to allow this TVto access the DMS.
This TV's MAC address can be confirmed at MAC
Address (_-_-_page68). Make sure that the contents of
the DMS are compatible with the formats which this TV
supports.
* If this TVcannot playthe content of DMS, makesure the
format is one of the formats which this TVsupports (_-_-_
pages78, 79 or 81).
For DLNA CERTIFIED TM Player
* Depending on the DMS, it may take time to display the
list.
For DLNA CERTIFIED _ Renderer
* Dependingthe state of this TV, DMCmay not be able to
control a DMR playback.
* If DMR playback start regardless a user intention, check
the access control of DMS or set Media Renderer to Off.
LEDindications
The Power and On Timer LED lights on the front of the
TV indicate the TV's status, as described below.
TV front
POW
On Timer Power
LED Indication
Power On/Standby LED
° Green is ON (solid}
The TV is operating properly.
• Orange is ON (solid)
Standby with Power-On Mode set to Fast. See "Power-
On Mode" (_#r_page 52).
• Green blinks three times
TV is powering up. Wait several seconds until the
green LED stops blinking.
• Green blinks
Abnormal operation of BUS line. Turn OFF the TV and
unplug the power cord. Plug the power cord in again
and turn ON the TV.
• Red blinks
Power-On Failure. Turn OFF the TV and unplug the
power cord. Plug the power cord in again and turn
ON the TV.
• Orange blinks
Abnormal operation of back light. Tulll OFF the TV
and unplug the power cord. Plug the power cord in
again and turn ON the TV.
On Timer LED
• Green is ON (solid)
On Timer is set.
• Green blinks (if applicable)
Fan Stopped. Turn OFF the TV and unplug the power
cord. Plug the power cord in again and turn ON the
TV.
If, after trying the solutions, the problem still exists:
° In the U.S., call TACP Consumer Solutions at 1-800-
631-3811.
In Canada, locate the nearest Toshiba authorized
service depot by directing your web browser to
www.toshiba.ca; click "Home Entertainment," and
then click "Support."
85
To Next Page
Loading...
Need help?
General
Weight and Dimensions
