:SENSe:WAVelength:SRANge
Function Sets/queries whether to limit a sweep range to
the spacing between line markers L1 and L2.
Syntax
:SENSe:WAVelength:SRANge<wsp>OFF|
ON|0|1
:SENSe:WAVelength:SRANge?
Response 0 = OFF, 1 = ON
Example
:SENSE:WAVELENGTH:SRANGE ON
:SENSE:WAVELENGTH:SRANGE? -> 1
Explanation This is a sequential command.
:SENSe:WAVelength:STARt
Function Sets/queries the measurement condition
measurement start wavelength.
Syntax
:SENSe:WAVelength:STARt<wsp><NRf>
[M|HZ]
:SENSe:WAVelength:STARt?
<NRf>=Measurement center wavelength [m]
Response
<NRf> [m|Hz] (AQ6370C/AQ6370D/AQ6373/
AQ6373B)
<NRf> [m|Hz|m
-1
] (AQ6375/AQ6375B)
Example
:SENSE:WAVELENGTH:START 1540.000NM
:SENSE:WAVELENGTH:START?->
+1.54000000E-006
Explanation • For the AQ6375/AQ6375B, to set using the
wavenumber, do not add any units when
in Wavenumber mode, and just enter the
numerical value.
• This is a sequential command.
:SENSe:WAVelength:STOP
Function Sets/queries the measurement condition
measurement stop wavelength.
Syntax
:SENSe:WAVelengthSTOP<wsp><NRf>
[M|HZ]
:SENSe:WAVelength:STOP?
<NRf> = Measurement stop wavelength [m]
Response
<NRf> [m|Hz] (AQ6370C/AQ6370D/AQ6373/
AQ6373B)
<NRf> [m|Hz|m
-1
] (AQ6375/AQ6375B)
Example
:SENSE:WAVELENGTH:STOP 1560.000NM
:SENSE:WAVELENGTH:STOP?->
+1.56000000E-006
Explanation • For the AQ6375/AQ6375B, to set using the
wavenumber, do not add any units when
in Wavenumber mode, and just enter the
numerical value.
• This is a sequential command.
STATus Sub System Command
:STATus:OPERation:CONDition?
Function Queries the contents of the operation status
condition register.
Syntax
:STATus:OPERation:CONDiton?
Example
:STATUS:OPERATION:CONDITION? -> 1
Explanation This is a sequential command.
:STATus:OPERation:ENABle
Function Queries the contents of the operation status
Enable register.
Syntax
:STATus:OPERation:ENABle<wsp>
<integer>
:STATus:OPERation:ENABle?
<integer> = Contents of the operation status
enable register
Example
:STATUS:OPERATION:ENABLE 8
:STATUS:OPERATION:ENABLE? -> 8
Explanation This is a sequential command.
:STATus:OPERation[:EVENt]?
Function Queries the contents of the operation status
Event register.
Syntax
:STATus:OPERation[:EVENt]?
Example
:STATUS:OPERATION? -> 1
Explanation This is a sequential command.
:STATus:PRESet
Function Clears the event register and sets all bits of the
enable register.
Syntax
:STATus:PRESet
Example
:STATUS:PRESET
Explanation • When this command is executed, the registers
will be affected as follows.
• The operation status event register is cleared
to “0.”
• All bits of the operation status enable register
are set to “0.”
• The questionable status event register is
cleared to “0.”
• All bits of the questionable status enable
register are set to “0.”
• Even when this command is executed, the
standard event status register and standard
event status enable register do not change.
• This is a sequential command.
7.6 Instrument-Specific Commands
To Next Page
Loading...
Need help?
General
