Pioneer VSX 1020 User Manual

Using other functions 08
75
En
English
Français
Deutsch
Nederlands
Italiano
Español
Resetting the system
Use this procedure to reset all the receiver’s
settings to the factory default. Use the front panel
controls to do this. Set
MULTI-ZONE to OFF .
• Disconnect the iPod and USB memory
device from the receiver beforehand.
1 Switch the receiver into standby.
2 While holding down
ENTER on the front
panel, press
 STANDBY/ON .
The display shows RESET  NO .
3 Select ‘ RESET ’ using PRESET / , then
press
ENTER on the front panel.
The display shows RESET? OK.
4 Press ENTER to confirm.
OK
appears in the display to indicate that the
receiver has been reset to the factory default settings.
• Note that all settings will be saved, even if
the receiver is unplugged.
Default system settings
Setting Default
Digital Video Conversion ON
SPEAKERS A
Speaker System Normal(SB/FH)
Speaker Setting Front: SMALL
Center: SMALL
FH/FW: SMALL
Surr: SMALL
SB: SMALLx2
SW: YES
Surround Position IN REAR
Crossover 80 Hz
X-Curve OFF
DIMMER brightest
Inputs
See Input function default and possible settings on
page 41.
HDMI
HDMI Audio Amp
Control ON
Control Mode ALL
DIsplay Power Off YES
DSP
Power On Level LAST
Volume Limit OFF
Mute Level FULL
Phase Control ON
Sound Retriever ON
(iPod/USB, INTERNET
RADIO, ADAPTER PORT
function)/
OFF (Other functions)
Sound Delay 0.0 frame
Dual Mono CH1
DRC AUTO
SACD Gain 0 dB
LFE Attenuate 0 dB
Auto delay OFF
Digital Safety OFF
Effect Level 90 (EXT.STEREO)/
50 (Other modes)
2 PL II Music Options Center Width:3
Dimension:0
Panorama:OFF
Neo:6 Options Center Image:
3 (Neo:6 MUSIC)/
10 (Neo:6 CINEMA)
Listening Mode
(All Inputs)
AUTO SURROUND
(2 ch/multi ch)/
STEREO (Head phones)
See also Setting the Audio options on page 67 for
other default DSP settings.
MCACC
MCACC Position Memory M1: MEMORY 1
Channel Level (M1 to M6) 0.0 dB
Speaker Distance
(M1 to M6)
10’00”
Standing Wave
(M1 to M6)
ATT of all channels/
filters: 0.0 dB
SWch Trim: 0.0 dB
EQ Data (M1 to M6) All channels/bands: 0.0 dB
EQ Trim: 0.0 dB
Setting Default
VSX-1020_UC.book 75 ページ ２０１０年１月７日 木曜日 午後６時０分

Pioneer VSX 1020 Specifications

General

Impedance	6 Ω
Frequency range	5 - 100000 Hz
Audio output channels	7.1 channels
Audio A/D Converter (ADC)	24-bit/96kHz
Signal-to-Noise Ratio (SNR)	100 dB
Total Harmonic Distortion (THD)	1 %
Audio system	Dolby TrueHD, DTS-HD Master Audio
Output power	140 W
Channels quantity	63 channels
Dimensions (WxDxH)	420 x 379 x 158 mm
Power requirements	AC 220 - 230 V, 50/60 Hz
HDMI ports quantity	7
Connectivity technology	Wired
Digital audio optical in	2
Product color	Black
Power consumption (standby)	0.6 W
Power consumption (typical)	245 W
Headphone connectivity	3.5 mm

Weight and Dimensions

Weight	10200 g