Husqvarna TC 85 User Manual

7 PREPARING FOR USE
23
7.2 Running in the engine
– During the running-in phase, do not exceed the specified engine performance.
Guideline
Maximum engine performance
During the first 3 operating hours < 70 %
During the first 5 operating hours < 100 %
– Avoid fully opening the throttle!
7.3 Preparing the vehicle for difficult riding conditions
Info
Use of the vehicle under difficult conditions, such as on sand or on wet and muddy surfaces, can lead
to considerably more rapid wear of components such as the drive train, brake system, or suspension
components. For this reason, it may be necessary to inspect or replace parts before the next scheduled
service.
– Clean the air filter and air filter box. ( p. 57)
Info
Check the air filter approx. every 30 minutes.
– Check the electrical connector for humidity and corrosion and to ensure it is firmly seated.
» If humidity, corrosion, or damage is found:
– Clean and dry the connector, or change it if necessary.
Difficult riding conditions are:
– Rides on dry sand. ( p. 23)
– Rides on wet sand. ( p. 25)
– Rides on wet and muddy circuits. ( p. 25)
– Rides at high temperatures or slow riding. ( p. 26)
– Riding at low temperatures and in snow. ( p. 27)
7.4 Preparing vehicle for rides on dry sand
– Make sure that no radiator covers ( p. 90) are installed.
V00814-01
– Check the radiator cap.
Value on the radiator cap 1.8 bar (26 psi)
» If the indicated value does not correspond to the setpoint
value:

Husqvarna TC 85 Specifications

General

Starter	Kickstarter
Transmission	6-speed
Engine Type	Single-cylinder, 2-stroke
Displacement	84.9 cc
Clutch	Wet multi-disc
Front Brake	Disc brake
Rear Brake	Disc brake
Front Tire	70/100
Rear Tire	90/100
Wheelbase	1290 mm
Final Drive	Chain

Summary

Safety Advice

Intended Use and Misuse

Defines how the vehicle should and should not be used to prevent danger.

Degrees of Risk and Symbols

Explains the different levels of risk and associated warning symbols used in the manual.

Safe Operation

Guidelines for operating the vehicle safely, covering risks and precautions.

Important Notes

Manufacturer Warranty and Service

Information on warranty validity, service requirements, and authorized workshops.

Customer Service

Information on how to contact authorized dealers for support and questions.

Controls

Handlebar Controls

Identifies and describes the function of levers and switches on the handlebar.

Levers and Starting Aids

Describes the function and operation of foot brake, kick starter, and plug-in stand.

Preparing for Use

Advice on First Use

Key considerations and warnings for a child's first ride on the motorcycle.

Engine Break-in

Instructions for the initial running-in phase of the engine for optimal performance.

Riding Conditions Preparation

Guidance on preparing the vehicle for various riding conditions like sand or mud.

Riding Instructions

Pre-ride Checks

Essential checks to perform before every trip to ensure safe operation.

Starting and Shifting

Procedures for starting the engine and properly shifting gears.

Braking and Stopping

Proper techniques for applying brakes and stopping the vehicle safely.

Service Schedule

Required Work

Lists essential maintenance tasks and their intervals for regular upkeep.

Recommended Work

Suggests additional maintenance tasks for optimal vehicle longevity.

Tuning the Chassis

Basic Chassis Setting

How to set up the chassis based on rider weight for optimal handling.

Fork Adjustment

Procedures for adjusting fork air pressure and compression damping.

Shock Absorber Adjustment

Instructions for adjusting compression and rebound damping of the shock absorber.

Service Work on the Chassis

Fork Procedures

Steps for removing, installing, and maintaining fork components.

Chain Maintenance

Steps for cleaning, checking tension, and maintaining the drive chain.

Brake System Procedures

Instructions for checking and maintaining brake fluid and linings.

Tuning the Engine

Throttle Cable Adjustment

Procedure for adjusting the play in the throttle cable for smooth operation.

Carburetor Setting

Details on adjusting carburetor settings for optimal engine performance.

Service Work on the Engine

Gear Oil Maintenance

Procedures for checking and changing engine gear oil.

Cleaning, Care

Cleaning the Motorcycle

Guidelines for washing and maintaining the motorcycle's appearance.

Troubleshooting

Common Faults and Solutions

Identifies common problems and provides steps to resolve them.

Technical Data

Engine Specifications

Key technical details about the motorcycle's engine.

Chassis Data

Specifications related to the motorcycle's frame, suspension, and wheels.