KEB COMBIVERT F4-C Applications Manual

13 1
KEB COMBIVERT F4-C
6
Name: Basis
25.03.98
Annex Search and Find
Chapter
Section Page Date
© KEB Antriebstechnik, 1997
All Rights reserved
Pn.19 6.9.10
Pn.33 6.9.8
Pn.34 6.9.9
Pn.36 6.9.9
Pn.38 6.9.8
Pn.42 6.9.7, 6.9.9, 6.9.10
Pn.43 6.9.10
Pn.50 6.7.7
Pn.52...58 6.9.19
PNP 3.1.7
POFF 6.3.11
Pole number 11.2.4
Power-Off 6.1.7
control 6.9.9
function 6.9.7
mode 6.3.11, 6.9.8
Pr-parameter 5.1.3
Pr. 4... 6 11.2.4
Pr. 7... 9 11.2.5
Pr. 8 6.4.5
Pr.10 11.2.5
Pr.11 11.2.5
Pr.16 11.2.5
Pr.18 11.2.6
Pr.25 11.2.6
Pr.27 11.2.6
Pr.37 11.2.6
Pr.38 6.4.5, 11.2.6
Pr.39...41 11.2.7
Profibus-DP 11.1.3
Operator 11.1.3
Profile parameter 6.4.5, 11.2.4
Project Planning 10.1.3
PTC-Warning 6.3.11
R
rAcc 6.3.11
Ramp
generator 6.4.12
mode 6.4.12, 6.4.16
stop 4.3.7, 6.3.11, 6.7.3
activation 6.7.3
Rated
motor
current 6.6.3, 6.7.9
frequency 6.6.3
output factor 6.6.3
speed 6.6.3
voltage 6.6.3
point 6.5.3
Ready-for-operation
signal 4.3.11
Record of changes 1.1.15
REF
4.3.12, 6.2.3, 6.2.7, 6.4.3, 6.4.5
Gain 6.1.18
Offset 6.1.18
Relay output 4.3.3, 4.3.11
Reset-Mode ST 6.3.8
Resetting of
error messages 4.1.5
peak values 4.1.5
Restart
delay 6.9.10
frequency 6.9.10
Rotation
presetting 6.3.7
setting 4.4.4, 6.4.6
RS232/485 11.1.3, 11.1.4, 13.1.11
ru-parameter 5.1.3
ru. 0 6.1.3, 6.3.11
ru. 1 6.1.8, 6.10.10
ru. 3 6.1.8, 6.3.11
ru. 4 6.1.8
ru. 6 6.4.12
ru. 7 6.3.11
ru. 9 6.7.9
ru.10 6.3.11
ru.14 6.3.4
ru.15 6.1.11, 6.3.13
ru.16 6.1.11, 6.3.8
ru.17 6.1.12
ru.18 6.1.12
ru.22 6.1.12, 6.2.3
ru.23 6.1.12, 6.2.3
ru.24 6.1.13
ru.29 6.1.13
ru.30 6.1.13, 6.4.5
ru.31 6.1.13
ru.32 6.1.13
ru.33 6.1.14, 6.9.18
ru.34 6.1.14, 6.9.15
ru.41 6.1.14, 6.2.8
ru.43 6.1.14, 6.9.23
ru.44 6.1.14
ru.45 6.1.15, 6.2.3
ru.46 6.1.15
ru.47 6.1.15, 6.10.10
Run-Signal 4.3.11
S
S-curve 6.4.14
time 6.4.14
Selection
of a parameter 4.1.4
of parameter sets 6.8.4
of set value 6.4.6
output conditions 6.3.12
setpoint value 6.2.7
Service 4.2.3
Set
-point
selection 7.2.4
signal 4.3.3, 4.3.12
digital
inputs 6.3.4
value
and ramp adjustment 6.4.3
calculation 6.4.10
calculation % 6.11.7
from PI-Control 6.4.3
from speed detection 6.4.3
limits 6.4.9
sources 6.4.5
Simulate Analog Option 6.2.7
Slip
compensation 4.3.3, 4.3.9, 6.11.6
control 6.9.8
SLL 4.3.7
Source
diameter compensation 6.11.10
parameter set 6.8.5
Special
functions 6.9.3
settings 4.3.7
Specifications 2.1.6
Speed
actual value 11.2.5
detection 6.4.5
key 4.4.3
max. amount 11.2.5
measurement 6.10.7
min. amount 11.2.5
reference variable 11.2.6
search 4.3.3, 4.3.8,
6.1.6, 6.7.7, 13.1.11
mode 6.7.7
setpoint value 11.2.5

KEB COMBIVERT F4-C Specifications

General

Brand	KEB
Model	COMBIVERT F4-C
Category	DC Drives
Language	English