To Next Page

To Previous Page

102 Enhanced phone functions

Allowing "Busy When Dialling"

If you activate this function, an incoming call received while you are performing

dialling is rejected. The caller then hears the busy signal.

You can also configure this setting via the WBM interface  Page 198.

Settings Press the key shown.

Select and confirm the option shown.

if nec.j Enter and confirm the user password.

Select and confirm the option shown.

Settings

User

Configuration

Outgoing calls

Busy when dialling = No m

Yes l

Save & Exit l

Important Information3
- Trademarks3
- Location of the Telephone4
- Software Update4
- Product Support on the Internet4
- Table of Contents5
General Information11
- About this Manual11
  - Symbols Used in the Manual11
- Service12
- Intended Use12
- Telephone Type12
- Speakerphone Quality and Display Legibility12
- Single-Line Telephone/Multi-Line Telephone12
Getting to Know Your Openscape Desk Phone IP 35G/35G Eco13
- The User Interface of Your Openscape Desk Phone IP 35G/35G Eco13
- Display20
  - Idle Mode20
  - Context-Dependent Displays22
- Messages24
  - Calls24
  - Additional Notes on Call Lists25
- Program/Service Menu26
  - User Settings27
- Control and Monitoring Function29
- Ports on the Underside of the Phone30
  - Using Network Ports more Efficiently30
Basic Functions31
- Secure Voice Transmission31
- Emergency Mode31
- Answering a Call32
- Directed Pickup34
  - Accept Call34
  - Picking up the Held Call35
- Switching from Handset to Speakerphone Mode36
- Switching from Speakerphone Mode to the Handset37
- Open Listening37
- Activating/Deactivating the Microphone38
- Ending a Call38
- Group Call39
- Listening to Voicemail42
- Call Control (2Nd Alert)43
  - Two Calls Simultaneously43
  - During Dialling44
- Making Calls45
- Redial48
- Consulting a Second Party48
- Callback52
- Calling Back Missed Calls55
Call Forwarding56
- Standard Call Forwarding56
- Call Forwarding by Call Type62
Programmable Keys69
- List of Available Functions69
- Programming a Key70
  - Access the Programming Mode70
  - Select Key to be Programmed71
- Programming Enhanced Functions71
- Using Programmed Keys75
- Resetting Programmable Keys76
Enhanced Phone Functions77
- Incoming Calls77
- Making Calls98
- Conference103
Phonebooks and Call Lists108
- Personal Directory108
- Corporate Directory111
- Call Lists115
Making Calls with Multiple Lines118
- Incoming Calls118
  - Accepting Calls for the Primary Line118
  - Accepting Calls for Secondary Lines118
- Making Calls119
- During Calls121
- Direct Station Selection Keys125
- Settings for Multiline (Keyset)128
Privacy/Security132
- Activating and Deactivating the Ringer132
  - Activating and Deactivating the Ringer Permanently132
  - Deactivating the Ringer Temporarily for Incoming Calls and Reactivating It133
- DND (Do Not Disturb)133
- Security135
  - User Password135
  - Phone Locking138
Mobility140
- Mobility Scenarios140
- Logging on and off at the same Phone141
  - Logging on to the Phone141
  - Logging off from the Phone142
- Logging on at Different Telephones143
  - Logging on with Forced Logoff at a Remote Phone143
  - Logging on with Forced, Delayed Logoff at a Remote- Phone144
Openscape Voice Functions145
- Feature Toggle Key145
- Making Anonymous Calls146
- Creating a List for Selective Calls148
  - For Call Acceptance148
  - For Call Rejection149
- Anonymous Calls150
  - Rejecting150
  - Accepting150
- Using Abbreviated Dialling151
- Call Tracing151
- Hunt Group Functions152
  - Making a Line Busy152
  - Marking the Last Line in the Hunt Group Chain153
- Reachability154
  - Serial Call154
  - Parallel Call155
- Parking a Call156
  - Call Park156
  - Unparking156
- Silent Monitoring157
  - Active Silent Monitoring157
  - Muted Silent Monitoring158
- One-Way Intercom and Two-Way Intercom Function159
  - One-Way Intercom160
  - Two-Way Intercom160
- Announcing the Local Phone Number161
- Dialling the Last Caller161
  - Retrieving and Dialling the Last Answered Caller161
  - Retrieving and Dialling the Phone Number of the Last Caller Dialled161
- Picking up Out-Of-Hours Calls162
- Code Table for Openscape Voice Functions163
Impact Levels164
- Answering a Call with a Lower Impact Level164
- Calls to a Lower Impact Level165
  - Off-Hook Dialling165
  - Forwarding a Call with a Lower Impact Level165
- Conducting a Call with a Lower Impact Level166
Individual Phone Configuration167
- Display167
  - Setting Contrast167
- Date and Time168
- Audio172
- Tone and Indication with an Unsecured Voice Connection179
- Key Click180
- Setting the Language and Country181
  - Selecting a Language181
  - Country-Specific Settings183
- Alarm on Changing the IL184
- Network Information185
- Resetting User Data186
  - Initiating the Reset186
Call Recording187
- Recording Modes187
- Explanations of Recording188
- Recording Calls189
Diagnostic Information196
Web Interface (WBM Interface)198
- General198
- Calling up the WBM Interface198
Fixing Problems203
- Caring for Your Telephone203
- Troubleshooting203
- Contact Partner in the Case of Problems203
- Labeling Keys204
Local User Menu205
- Opening the User Menu on the Phone205
- User Menu Display205
  - Key Functions213
Index215

Brand	Unify
Model	OpenScape IP 35G SIP
Category	IP Phone
Language	English

Unify OpenScape IP 35G SIP User Manual

Table of Contents

Questions and Answers:

Unify OpenScape IP 35G SIP Specifications

Related product manuals