Juniper SRX345 Hardware Guide

Viewing SRX345 Services Gateway Factory-Default Settings
To view the factory-default configuration of the services gateway using the CLI:
1. Verify that the services gateway is powered on.
2. Log in as the root user and provide your credentials.
3. In shell mode, navigate to the /etc/config folder.
% cd /etc/config
4. View the list of default config files.
% ls
The following sample output displays the list of factory-default configuration files:
blv-defaults.conf srx210he2-factory.conf
ex9204-factory.conf srx210he2-poe-defaults.conf
ex9208-factory.conf srx210he2-poe-factory.conf
ex9214-factory.conf srx220-8xge-factory.conf
j-series-defaults.conf srx220-poe-8xge-factory.conf
jnu-factory.conf srx220h-defaults.conf
jsrxsme-series-defaults.conf srx220h-factory.conf
jsrxsme-series-factory.conf srx220h-poe-defaults.conf
junos-defaults.conf srx220h-poe-factory.conf
junos-factory.conf srx220h2-defaults.conf
junos-fips-defaults.conf srx220h2-factory.conf
ptx-series-defaults.conf srx220h2-poe-defaults.conf
shmlog srx220h2-poe-factory.conf
srx100-8xfe-factory.conf srx240-16xge-factory.conf
srx100b-defaults.conf srx240-poe-16xge-factory.conf
srx100b-factory.conf srx240b-factory.conf
srx100h-defaults.conf srx240b2-factory.conf
srx100h-factory.conf srx240h-dc-defaults.conf
srx100h2-defaults.conf srx240h-dc-factory.conf
srx100h2-factory.conf srx240h-defaults.conf
srx110-8xfe-vdsl-factory.conf srx240h-factory.conf
srx110-8xfe-vdsl-wl-factory.conf srx240h-poe-defaults.conf
srx110-8xfe-wl-factory.conf srx240h-poe-factory.conf
srx110b-defaults.conf srx240h2-dc-defaults.conf
srx110b-va-defaults.conf srx240h2-dc-factory.conf
srx110b-va-factory.conf srx240h2-defaults.conf
srx110b-vb-defaults.conf srx240h2-factory.conf
srx110b-vb-factory.conf srx240h2-poe-defaults.conf
srx110b-wl-defaults.conf srx240h2-poe-factory.conf
srx110b-wl-factory.conf srx300-8xge-factory.conf
srx110h-defaults.conf srx300-defaults.conf
srx110h-va-defaults.conf srx300-factory.conf
srx110h-va-factory.conf srx300-lem-factory.conf
srx110h-va-wl-defaults.conf srx320-8xge-factory.conf
srx110h-va-wl-factory.conf srx320-defaults.conf
srx110h-vb-defaults.conf srx320-factory.conf
srx110h-vb-factory.conf srx320-lem-factory.conf
srx110h-vb-wl-defaults.conf srx320-poe-8xge-factory.conf
srx110h-vb-wl-factory.conf srx320-poe-defaults.conf
69Copyright © 2017, Juniper Networks, Inc.
Chapter 18: Performing the Initial Configuration

Juniper SRX345 Specifications

General

USB 2.0 ports quantity	1
Ethernet LAN (RJ-45) ports	8
Flash memory	8000 MB
Internal memory	4000 MB
Certification	FCC A, RoHS 2
Rack capacity	1U
Heat dissipation	420 BTU/h
Power consumption (typical)	122 W
Storage temperature (T-T)	-20 - 70 °C
Operating temperature (T-T)	0 - 40 °C
Storage relative humidity (H-H)	5 - 95 %
Operating relative humidity (H-H)	10 - 90 %
Routing protocols	BGP, CLNS, MPLS, OSPF, RIP-1, RIP-2
Supported network protocols	IPv4, IPv6
Firewall security	Yes
Security algorithms	IPSEC, SSL/TLS
Networking standards	IEEE 802.1p
Ethernet LAN data rates	10, 100, 1000 Mbit/s

Weight and Dimensions

Weight	4900 g
Dimensions (WxDxH)	440.9 x 370.1 x 43.6 mm