Juniper SRX345 Hardware Guide

srx110h-wl-defaults.conf srx320-poe-factory.conf
srx110h-wl-factory.conf srx320-poe-lem-factory.conf
srx110h2-va-defaults.conf srx340-16xge-factory.conf
srx110h2-va-factory.conf srx340-defaults.conf
srx110h2-vb-defaults.conf srx340-factory.conf
srx110h2-vb-factory.conf srx340-lem-factory.conf
srx210-2xge-6xfe-factory.conf srx345-defaults.conf
srx210-poe-2xge-6xfe-factory.conf srx345-factory.conf
srx210b-defaults.conf srx345-lem-factory.conf
srx210b-factory.conf srx550-6xge-factory.conf
srx210be-defaults.conf srx550-defaults.conf
srx210be-factory.conf srx550-factory.conf
srx210h-defaults.conf srx550m-6xge-factory.conf
srx210h-factory.conf srx550m-defaults.conf
srx210h-poe-defaults.conf srx550m-factory.conf
srx210h-poe-factory.conf srx650-4xge-factory.conf
srx210he-defaults.conf srx650-defaults.conf
srx210he-factory.conf srx650-factory.conf
srx210he-poe-defaults.conf subs-mgmt-proc-set
srx210he-poe-factory.conf vrr-series-defaults.conf
srx210he2-defaults.conf
5. View the required default config file.
% vi config file name
Related
Documentation
SRX345 Services Gateway Software Configuration Overview on page 67•
• Understanding SRX345 Services Gateway Factory-Default Settings on page 68
• Accessing J-Web on the SRX345 Services Gateway on page 71
• Configuring the SRX345 Services Gateway Using the J-Web Setup Wizard on page 72
• Accessing the CLI on the SRX345 Services Gateway on page 76
• Connecting to the SRX345 Services Gateway from the CLI Remotely on page 77
• Configuring the SRX345 Services Gateway Using the CLI on page 78
Configuring Zero-Touch Provisioning on the SRX345 Services Gateway
Zero Touch Provisioning (ZTP) enables you to complete the initial configuration of the
SRX345 Services Gateway in your network automatically, with minimum intervention.
Network Service Controller is a component of the Juniper Networks Contrail Service
Orchestration platform that simplifies and automates the design and implementation
of custom network services that use an open framework. For more information, refer to
the Network Service Controller section in the datasheet at
http://www.juniper.net/assets/us/en/local/pdf/ datasheets/1000559-en.pdf.
NOTE: To complete the ZTP process, ensure that the services gateway is
connected to the Internet.
Copyright © 2017, Juniper Networks, Inc.70
SRX345 Services Gateway Hardware Guide

Juniper SRX345 Specifications

General

USB 2.0 ports quantity	1
Ethernet LAN (RJ-45) ports	8
Flash memory	8000 MB
Internal memory	4000 MB
Certification	FCC A, RoHS 2
Rack capacity	1U
Heat dissipation	420 BTU/h
Power consumption (typical)	122 W
Storage temperature (T-T)	-20 - 70 °C
Operating temperature (T-T)	0 - 40 °C
Storage relative humidity (H-H)	5 - 95 %
Operating relative humidity (H-H)	10 - 90 %
Routing protocols	BGP, CLNS, MPLS, OSPF, RIP-1, RIP-2
Supported network protocols	IPv4, IPv6
Firewall security	Yes
Security algorithms	IPSEC, SSL/TLS
Networking standards	IEEE 802.1p
Ethernet LAN data rates	10, 100, 1000 Mbit/s

Weight and Dimensions

Weight	4900 g
Dimensions (WxDxH)	440.9 x 370.1 x 43.6 mm