To Next Page

To Previous Page

ERGONOMICS 8

8.6 Adjusting the basic position of the hand brake lever

H01289-10

– Push the hand brake lever forward.

– Adjust the basic position of the hand brake lever to your hand

size by turning adjusting screw

Info

Turn the adjusting screw clockwise to increase the

distance between the hand brake lever and the han-

dlebar.

Turn the adjusting screw counterclockwise to decrease

the distance between the hand brake lever and the han-

dlebar.

The range of adjustment is limited.

Only turn the adjusting screw by hand, and do not use

force.

Do not make any adjustments while riding.

Default Chapter5
- Table of Contents5
1 Means of Representation 111
- Symbols Used11
- Formats Used12
2 Safety Advice 213
- Use Definition - Intended Use13
- Misuse13
- Degrees of Risk and Symbols14
- Tampering Warning15
- Safe Operation15
- Protective Clothing17
- Work Rules17
- Environment18
- Owner's Manual18
3 Important Notes 319
- Manufacturer and Implied Warranty19
- Operating and Auxiliary Substances19
- Spare Parts, Accessories19
- Service20
- Figures20
- Customer Service20
4 View of Vehicle22
- View of Vehicle, Front Left (Example)22
- View of Vehicle, Rear Right (Example)24
5 Serial Numbers26
- Chassis Number26
- Type Label26
- Key Number27
- Engine Number27
- Fork Part Number28
- Shock Absorber Article Number28
- Steering Damper Article Number29
6 Controls30
- Clutch Lever30
- Hand Brake Lever30
- Throttle Grip31
- Switches on the Left Side of the Handlebar31
- Combination Switch, Left Side31
- Light Switch32
- Hazard Warning Flasher Switch33
- Menu Switch34
- Turn Signal Switch34
- Horn Button35
- Switches on the Right Side of the Handlebar36
- Combination Switch, Right36
- Emergency off Switch37
- Switch for the Cruise Control System37
- Upper Button of the Cruise Control System40
- Lower Button of the Cruise Control System41
- Electric Starter Button42
- Locking the Steering42
- Unlocking the Steering43
- Socket for Electrical Accessories44
- Ignition/Steering Lock44
- Immobilizer45
- Opening the Filler Cap46
- Closing the Filler Cap48
- Seat Lock50
- Tool Set50
- Grab Handle51
- Case Holders51
- Passenger Footrests52
- Shift Lever53
- Foot Brake Lever54
  - Side Stand54
7 Combination Instrument56
- Overview56
- Activation and Test56
- Matrix Display57
- Segment Display58
- Fuel Level Display59
- Indicator Lamps60
- Message on the Matrix Display62
- Shift Warning Light64
- Service Display65
- Matrix Display Menu66
- Favorites66
- Trip 166
- Trip 267
- General Info68
- Tpms69
- Set Favorites70
- Settings71
- Warning71
- Heating72
- Mtc/Abs72
- Load74
- Damping74
- Drive Mod75
- Menu Overview76
- Language77
- Distance78
- Temp78
- Pressure79
- Fuel Cons79
- Clock/Date80
- Shift Light80
- Heat Grip81
- Clighttest82
- Drl83
- Quick Shift84
8 Ergonomics 885
- Handlebar Position85
- Adjusting the Handlebar Position85
- Adjusting the Steering Angle89
- Adjusting the Windshield90
- Adjusting the Basic Position of the Clutch Lever92
- Adjusting the Basic Position of the Hand Brake Lever93
- Adjusting the Basic Position of the Foot Brake Lever94
- Setting the Step Plate of the Foot Brake Lever95
- Checking the Basic Position of the Shift Lever96
- Adjusting the Basic Position of the Shift Lever97
- Setting the Shift Lever Stub98
9 Preparing for Use 999
- Advice on Preparing for First Use99
- Running in the Engine101
- Loading the Vehicle101
10 Riding Instructions104
- Checks and Maintenance Measures When Preparing for Use104
- Starting the Vehicle105
  - Starting off107
- Start off with HHC (Option: Hill-Start Assist)108
- Quickshifter109
- Shifting, Riding110
- MSR (Option: Engine Braking Control)116
- Applying the Brakes117
- Stopping, Parking119
- Transporting121
- Refueling122
11 Service Schedule 11125
- Additional Information125
- Required Work125
- Recommended Work128
12 Suspension Setting 12129
- Fork/Shock Absorber129
- Load129
- Damping130
13 Service Work on the Chassis 13131
- Raising the Motorcycle with the Rear Lifting Gear131
- Removing the Rear of Motorcycle from the Lifting Gear131
- Lifting the Motorcycle with the Front Lifting Gear132
- Taking the Motorcycle off the Front Lifting Gear133
- Removing the Passenger Seat134
- Mounting the Passenger Seat135
- Removing the Front Rider's Seat135
- Mounting the Front Rider's Seat137
- Removing the Windshield138
- Installing the Windshield138
- Removing the Main Silencer139
- Installing the Main Silencer140
- Checking the Chain for Dirt142
- Cleaning the Chain142
- Checking the Chain Tension144
- Adjusting the Chain Tension146
- Checking the Chain, Rear Sprocket, Engine Sprocket, and Chain Guide147
- Checking/Correcting the Fluid Level of the Hydraulic Clutch152
- Removing the Tank Spoiler155
- Installing the Tank Spoiler156
- Removing Front Fender158
- Installing Front Fender158
- Cleaning the Dust Boots of the Fork Legs159
14 Brake System 14161
- Antilock Brake System (ABS)161
- Checking the Brake Discs165
- Checking the Front Brake Fluid Level166
- Adding Front Brake Fluid167
- Checking the Front Brake Linings170
- Checking the Rear Brake Fluid Level171
- Adding Rear Brake Fluid172
- Checking the Brake Linings of the Rear Brake174
15 Wheels, Tires176
- Removing the Front Wheel176
- Installing the Front Wheel178
- Removing the Rear Wheel181
- Installing the Rear Wheel183
- Checking the Tire Condition186
- Checking the Tire Air Pressure188
16 Electrical System190
- Daytime Running Light (DRL)190
- Cornering Headlight191
- Removing the Battery192
- Installing the Battery194
- Recharging the Battery197
- Changing the Main Fuse202
- Changing the Fuses in the Fuse Box204
- Changing the Headlight Bulb207
- Checking the Setting of the Lighting System209
- Adjusting the Headlight Range212
- Adjusting the Cornering Light Range213
- Activating/Deactivating the Ignition Key216
- Diagnostics Connector222
- Front ACC1 and ACC2222
- ACC1 and ACC2 Rear223
17 Cooling System224
- Checking the Coolant Level in the Compensating Tank224
- Correcting the Coolant Level in the Compensating Tank226
18 Engine Tuning228
- Drive Mod228
- Motorcycle Traction Control (MTC)229
19 Service Work on the Engine230
- Checking the Engine Oil Level230
- Changing the Engine Oil and Oil Filter, Cleaning the Oil Screens231
- Adding Engine Oil238
20 Cleaning, Care 20241
- Cleaning Motorcycle241
- Checks and Maintenance Steps for Winter Operation244
21 Storage246
- Preparing for Use after Storage248
22 Troubleshooting 22249
23 Technical Data252
- Engine252
- Engine Tightening Torques254
- Capacities259
- Engine Oil259
- Coolant259
- Fuel259
- Chassis260
- Electrical System261
- Tires262
- Fork262
- Shock Absorber263
- Chassis Tightening Torques263
24 Declarations of Conformity 24271
25 Substances 25275
- Auxiliary Substances 26279
27 Standards 27281
28 Index of Special Terms282
29 List of Abbreviations 29283
30 List of Symbols284
- Red Symbols284
- Yellow and Orange Symbols284
- Green and Blue Symbols285
- Index286

Brand	KTM
Model	1290 Super Duke GT 2018
Category	Motorcycle
Language	English

KTM 1290 Super Duke GT 2018 User Manual

Table of Contents

Other manuals for KTM 1290 Super Duke GT 2018

Questions and Answers:

KTM 1290 Super Duke GT 2018 Specifications

Related product manuals