Yealink SIP-T41S Administrator's Guide

Administrator’s Guide for SIP-T2 Series/T4 Series/T5 Series/CP920 IP Phones
260
######Set a Park key######
linekey.1.type = 10
linekey.1.value =*01
linekey.1.line = 1
linekey.1.label =Bill
######Set a Retrieve key####
linekey.3.type = 56
linekey.3.line = 1
linekey.3.value =*11
linekey.3.label =Retrieve Bill
After provisioning, you can easily press the Park key (line key 1) to park a call to the specific shared parking lot
(*01) during a call, and press the Retrieve key (line key 3) to retrieve the parked call from the shared parking lot
(*01) using the retrieve code (*11). You can only perform call park feature on the specific line (line 1).
If the “features.call_park.line_restriction.enable” is set to 0 (Disabled), the phone will park/retrieve the call to the
server on the current line in use.
Note: In Transfer call park mode, if you press the Park key when the phone is idle, the Park key will invoke the call park
code. Therefore, you can use a Park key to park and retrieve a call. In this case, you need to assign the park retrieve code
(*11) to “features.call_park.park_code”. When you press the Park key again on the idle screen, the phone will dial out “*11*01”
to retrieve the parked call.
Example: Setting a Line Key as Directed Pickup Key
Scenario Conditions Related Topic
account.1.direct_pickup_code = *97
or
features.pickup.direct_pickup_code = *97
Directed Call Pickup
Example
linekey.1.type = 9
linekey.1.line =1
linekey.1.value= 4603
linekey.1.label=Bill
After provisioning, you can easily press the Directed Pickup key (line key 1) to pick up an incoming call to a specific
phone (4603).
Note: The Directed Pickup invokes the directed pickup code by default. Therefore, the phone dials out *974603 to pick up a
call. If the directed code is not set, you can assign code and extension to “linekey.X.value”, for example, “*974603”.
Example: Setting a Line Key as Group Pickup Key
The following example shows the configuration for a group pickup key.
Example
linekey.1.type = 23
linekey.1.line =1
linekey.1.value =*98

Yealink SIP-T41S Specifications

General

Mounting	Desk/Wall
Handset type	Wired handset
Product type	IP Phone
Product color	Black
Keypad illumination	Yes
Wi-Fi	No
Networking standards	IEEE 802.3af
Ethernet LAN data rates	10, 100 Mbit/s
Ethernet LAN interface type	Fast Ethernet
Supported network protocols	SIP v1, SIP v2, LLDP/CDP/DHCP, OpenVPN, IEEE802.1X, IPv6, FTP/TFTP/HTTP/HTTPS
Volume control	Digital
Number of programmable keys	6
Lines quantity	6 lines
Phonebook capacity	1000 entries
Dual-Tone Multi-Frequency (DTMF) modes	In-band, Out-of band, SIP info
Input frequency	50/60 Hz
AC adapter input voltage	100 - 240 V
AC adapter output current	1.2 A
AC adapter output voltage	5 V
Display diagonal	2.7 \
Display resolution	192 x 64 pixels
Operating temperature (T-T)	-10 - 50 °C
Operating relative humidity (H-H)	10 - 95 %
Voice codecs	CNG, G.711Mu, G.711a, G.723.1, G.726, G.729ab, VAD, iLBC
Certification	CE
Cables included	LAN (RJ-45)
Number of handles included	1 pc(s)
Harmonized System (HS) code	85171800

Weight and Dimensions

Depth	189 mm
Width	212 mm
Height	175 mm
Package depth	223 mm
Package width	246 mm
Package height	120 mm