Yealink SIP-T41S Administrator's Guide

Phone Customization
283
Power Saving Configuration
You can enable or disable power saving, and set the different idle timeout for office hours and off hours.
l
Office Hour: specify the start time and end time of the day’s office hour. You can change the office hours to avoid
affecting your work.
l
Idle Timeout: specify the period of time before the IP phone enters the power-saving mode.
You can specify the following three types of idle timeout:
l
Office Hours Idle TimeOut: specify the idle timeout for office hours.
l
Off Hours Idle TimeOut: specify the idle timeout for non-office hours.
l
User Input Extension Idle TimeOut: specify the idle timeout that applies after you use the IP phone (for example,
press a key on the phone or pick up/hang up the handset).
By default, the Office Hours Idle Timeout is much longer than the Off Hours Idle TimeOut. If you use the IP phone,
the idle timeout that applies (User Input Extension Idle Timeout or Office Hours/Off Hours Idle TimeOut) is the
timeout with the highest value.
If the phone has an incoming call or new message, the User Input Extension Idle TimeOut is ignored.
Tip: You can choose to set a higher User Input Extension Idle TimeOut than the Office Hours Idle TimeOut and Off Hours Idle
TimeOut so that the phone does not enter the power-saving mode too often after you use the phone.
The following table lists the parameters you can use to configure power saving.
Parameter
features.power_saving.intelligent_mode <y0000000000xx>.cfg
Description
It enables or disables the power saving intelligent mode.
Permitted
Values
0-Disabled, the phone stays in power-saving mode even if the office hour arrives the next day.
1-Enabled, the phone automatically identifies the office hour and exits power-saving mode once the
office hour arrives the next day.
Default
1
Supported
Devices
All phones except T19(P) E2
Parameter
features.power_saving.enable <y0000000000xx>.cfg
Description
It enables or disables the power saving feature.
Permitted
Values
0-Disabled, the phone automatically enters the power-saving mode to protect the screen when the
phone is inactive for 72 hours. That is, the color screen phones will turn off the backlight and screen,
and the black-and-white screen phones will only turn off the backlight. Image persistence may be
caused by LCD.
1-Enabled
Default
1
Supported
Devices
All phones except T19(P) E2
Web UI
Settings > Power Saving > Power Saving
Parameter
features.power_saving.office_hour.idle_timeout <y0000000000xx>.cfg
Description
It configures the time (in minutes) to wait in the idle state before the phone enters power-saving mode
during the office hours.
Permitted
Values
Integer from 1 to 960
Default
960

Yealink SIP-T41S Specifications

General

Mounting	Desk/Wall
Handset type	Wired handset
Product type	IP Phone
Product color	Black
Keypad illumination	Yes
Wi-Fi	No
Networking standards	IEEE 802.3af
Ethernet LAN data rates	10, 100 Mbit/s
Ethernet LAN interface type	Fast Ethernet
Supported network protocols	SIP v1, SIP v2, LLDP/CDP/DHCP, OpenVPN, IEEE802.1X, IPv6, FTP/TFTP/HTTP/HTTPS
Volume control	Digital
Number of programmable keys	6
Lines quantity	6 lines
Phonebook capacity	1000 entries
Dual-Tone Multi-Frequency (DTMF) modes	In-band, Out-of band, SIP info
Input frequency	50/60 Hz
AC adapter input voltage	100 - 240 V
AC adapter output current	1.2 A
AC adapter output voltage	5 V
Display diagonal	2.7 \
Display resolution	192 x 64 pixels
Operating temperature (T-T)	-10 - 50 °C
Operating relative humidity (H-H)	10 - 95 %
Voice codecs	CNG, G.711Mu, G.711a, G.723.1, G.726, G.729ab, VAD, iLBC
Certification	CE
Cables included	LAN (RJ-45)
Number of handles included	1 pc(s)
Harmonized System (HS) code	85171800

Weight and Dimensions

Depth	189 mm
Width	212 mm
Height	175 mm
Package depth	223 mm
Package width	246 mm
Package height	120 mm