Zetor MAJOR CL User Manual

Hydrostatic steerin
g
z check tightness of screws and nuts of the control rods and levers
z check state of all hoses of hydraulic control circuits whether they are not damaged and oil is not leaking
Trailer brakes
Hitches
After work with front implements and in case of cooler clogging
Air brakes of the trailer
Check tightness of the air-brake system and braking
efficiency of the tractor with the trailer.
If the minimum air-pressure indicator on the
dashboard is off it means that air pressure in the
system of air-pressure brakes is sufficient.
Hydraulic brakes of the trailer
Check tightness of hygraulic-brake circuits in the trailer
and braking efficiency of the tractor with the trailer.
NM13N085
Check the condition of the hitching and attachment
systems of the tractor and trailer.
NM13N063
A
fter work with front implements
:
- Check the connections of the external hydraulic circuit of
the control of the front three-point hitch for leaks
Clogging of the coolers:
- Release and slide the cooler to the left side of the tractor.
- Clean the front walls of the engine (gearbox, air-
conditioning condenser) cooler with compressed air (blow
air in the direction from the engine).
- Remove residual dirt from the space under the hood so
that it should not be suctioned again.
C113
- release the screw (1) from the right side of the tractor
and tilt the oil cooler of the front PTO shaft
- clean the walls of the cooler with pressure air
PREVENTIVE DAILY MAINTENANCE
22

Zetor MAJOR CL Specifications

General

Brand	Zetor
Model	MAJOR CL
Category	Tractor
Language	English

Summary

User Safety Instructions

General Safety Regulations

Basic rules for safe tractor operation and compliance.

Engine Starting Safety

Procedures and precautions for starting the tractor engine safely.

Safe Driving Practices

Operational practices for safe driving and handling of the tractor.

Tractor Overturning Risks

Factors increasing rollover risk and prevention methods.

Fire Prevention Guidelines

Guidelines to prevent fires during operation and maintenance.

Daily Maintenance Precautions

Daily checks and maintenance tasks for the tractor's safety.

Front Loader Safety Procedures

Safe operating procedures for tractors equipped with front end loaders.

Preventive Daily Maintenance

Engine Oil Level Monitoring

Procedure for checking and maintaining the engine oil level.

Cooling System Integrity Check

Checks for leaks and coolant level in the engine cooling system.

Acquaintance with the Tractor

Information Display Interpretation

Display of operational data, fault notifications, and warning indicators.

Tractor Pedals and Differential Lock

Identification and operation of tractor pedals and the differential lock.

Gear, Direction, and PTO Controls

Operation of gear shifting, reversing levers, and PTO shaft controls.

Driving Operation

Pre-Start Engine Procedures

Pre-start checks and procedures for the engine.

Engine Starting Sequence

Step-by-step guide to starting the tractor engine safely.

Engine Starting Troubleshooting

Troubleshooting steps if the engine fails to start.

Error Signal Interpretation

Interpretation of dashboard warning lights, error codes, and signals.

Driving Away Safely

Step-by-step guide for driving the tractor away smoothly.

Differential Lock Engagement

Procedures for engaging and disengaging the differential lock.

Foot Brake Pedal Usage

Operation and connection of foot brake pedals for braking.

Tractor Stopping Procedures

Procedures for stopping the tractor using the manual brake and engine shutdown.

Running in the Tractor

New Tractor Break-in Principles

Core principles for breaking in a new tractor for the first 100 hours of operation.

Drive of Agricultural Machinery

PTO Shaft Safe Operation

Safe operation, connection, and use of PTO shafts and their covers.

PTO Shaft Control Mechanisms

Identification and function of PTO shaft control levers, buttons, and indicators.

Front PTO Shaft Operation

Specifications and operating procedures for the front PTO shaft.

Hydraulic System

Hydraulic System Components

Overview of hydraulic system components, pump, and pressure.

Internal Linkage Control Methods

Controls for three-point linkage adjustment (position, mixed, power).

External Hydraulic Circuit Usage

System for connecting external hydraulic devices via quick couplers and control elements.

Hitches

Rear Three-Point Linkage Specifications

Front Three-Point Hitch Operation

Tractor Maintenance

Service Inspection Schedule

Fluid and Filter Replacement Schedule

Maintenance Instructions

Engine Oil Level and Draining

Engine Oil Filter and Oil Replacement

Fuel Filter System Maintenance

Air Filter Element Servicing

Cooling System Coolant Replacement

Gearbox, Axle, and Hydraulic Oil Checks