Bosch DIVAR AN 5000 User Manual

Hardware setup
This chapter contains detailed information about the hardware installation and connection of
external equipment to the unit. The connector types and their pin signals are described. Most
of the connectors are located at the rear panel of the unit (see Connections, page 17). For
convenience, one USB port is located on the front of the unit to connect a mouse or memory
device.
All the input/output ports are Safety Extra Low Voltage (SELV) circuits. SELV circuits should
only be connected to other SELV circuits.
Camera connections
Connect cameras to the VIDEO IN connectors on the back of the unit using 75 ohm video
coaxial cables with BNC connectors. Optionally on the DIVAR AN 5000 VIDEO OUT connectors
(or the video out D-connector on the If the camera signal is looped through to additional
equipment, make sure that the end of the video connection is terminated with 75 ohm
termination.
The DIVAR can be configured as a PAL or NTSC unit by manually setting the TV standard to
PAL or NTSC in the General setup menu.
Specifications
Input signal: Composite video 1 Vpp, 75 ohm
TV standard: PAL/NTSC, menu select
Connector type: BNC looped-through, automatic termination
Audio connections
The DIVAR supports up to 4 audio inputs and 1 audio output, plus a Mic in port. Connect using
audio cable with RCA (CINCH) compatible connectors.
Specifications
Input signal: Mono RCA (CINCH), 1 Vpp, 10 kOhm
Audio output signal: Mono RCA (CINCH), 1 Vpp, 5 kOhm
Bidirectional (MIC IN): Mono talk input RCA, 200 to 3000 mV, 10 kOhm
Monitor connections
Up to three monitors can be simultaneously connected through the VGA MON. A,
HDMI MON. A or CVBS MON. A connections for live viewing, playback and user menus. A single
monitor can be connected through the CVBS MON. B connection for live viewing.
VGA output
Connect the unit to a VGA monitor using standard VGA cable. It is recommended to use
17” monitors or larger when using LCD.
Specifications
Output signal: VGA
Resolution: 1024x768 (4:3), 1280x720 (5:4), 1280x1024 and 1920x1080 for Monitor A
Color: True color (32 bit)
Connector type: D-SUB
CVBS
Connect the monitor A CVBS and/or monitor B CVBS output to monitors using 75 ohm video
coaxial cables with BNC connectors.
5
5.1
5.2
5.3
5.3.1
5.3.2
28 en | Hardware setup DIVAR AN 3000 / DIVAR AN 5000
2014.10 | 2.0 | AM18-Q0669 Operations Manual Bosch Security Systems

Bosch DIVAR AN 5000 Specifications

General

Motion sensor	Yes
Total storage capacity	2000 GB
Video compression formats	H.264
Analog signal format system	NTSC, PAL
Compatible operating systems	Windows XP, Windows Vista, Windows 7.
Playback resolutions supported	960x576, 960x480, 704x576, 704x480, 704x288, 704x240, 352x288, 352x240, 176x144, 176x120
Audio input	4
BNC input ports	16
USB 2.0 ports quantity	1
Ethernet interface type	Gigabit Ethernet
HDD interface	Serial ATA
Maximum HDD capacity	3000 GB
Power requirements	100-240VAC 50-60Hz
Optical drive included	No
Storage temperature (T-T)	-40 - 70 °C
Operating temperature (T-T)	0 - 40 °C
Operating relative humidity (H-H)	0 - 93 %

Weight and Dimensions

Dimensions (WxDxH)	440 x 420 x 70 mm