SUPPLEMENTAL INFLATABLE RESTRAINTS (SIR) 8B–59
DAEWOO M-150 BL2
DTC 24 – Ignition Input Circuit, Voltage Too Low
Step
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
Action
Value(s)
Yes
No
ÁÁ
1
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
Check the fuse F2.
Is the fuse blown?
ÁÁÁ
–
ÁÁÁÁÁ
Go to Step 2
ÁÁÁÁ
Go to Step 3
ÁÁ
ÁÁ
2
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
1. Check for a short circuit.
2. Repair if needed.
3. Replace the fuse.
Is the repair complete?
ÁÁÁ
ÁÁÁ
–
ÁÁÁÁÁ
ÁÁÁÁÁ
Go to
Diagnostic
System Check
ÁÁÁÁ
ÁÁÁÁ
–
ÁÁ
ÁÁ
3
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
1. Turn the ignition ON.
2. Using a multimeter, check the voltage at the fuse
F2.
Is the battery voltage available at the fuse F2?
ÁÁÁ
ÁÁÁ
11–14 v
ÁÁÁÁÁ
ÁÁÁÁÁ
Go to Step 5
ÁÁÁÁ
ÁÁÁÁ
Go to Step 4
ÁÁ
ÁÁ
4
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
Repair the power supply to the fuse F2.
Is the repair complete?
ÁÁÁ
ÁÁÁ
–
ÁÁÁÁÁ
ÁÁÁÁÁ
Go to
Diagnostic
System Check
ÁÁÁÁ
ÁÁÁÁ
–
ÁÁ
ÁÁ
ÁÁ
ÁÁ
ÁÁ
ÁÁ
ÁÁ
5
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
1. Disconnect the negative battery cable.
2. Wait one minute before proceeding.
3. Disconnect the connector at the SDM.
4. Reconnect the battery.
5. Turn the ignition key ON.
6. Measure the voltage at the terminal 5 of the SDM
Connector.
D Refer to ‘‘Diagnostic Illustration 11’’ in this
section.
Is the voltage equal to the specified value?
ÁÁÁ
ÁÁÁ
ÁÁÁ
ÁÁÁ
ÁÁÁ
ÁÁÁ
ÁÁÁ
11–14 v
ÁÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁÁ
Go to Step 6
ÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁ
Go to Step 7
ÁÁ
ÁÁ
6
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
1. Replace the SDM.
2. Reconnect the electrical connectors.
Is the repair complete?
ÁÁÁ
ÁÁÁ
–
ÁÁÁÁÁ
ÁÁÁÁÁ
Go to
Diagnostic
System Check
ÁÁÁÁ
ÁÁÁÁ
–
ÁÁ
ÁÁ
ÁÁ
ÁÁ
ÁÁ
ÁÁ
ÁÁ
7
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
1. Disconnect the connector C208.
D The connector C208 is the connector between
the instrument harness and the supplemental
inflatable restraints (SIR) harness.
2. Turn the ignition ON.
3. Using a multimeter, check the voltage on the
instrument harness side at the terminal 2 of the
connector C208.
D Refer to ‘‘Diagnostic Illustration 12’’ in this
section.
Is the voltage equal to the specified value?
ÁÁÁ
ÁÁÁ
ÁÁÁ
ÁÁÁ
ÁÁÁ
ÁÁÁ
ÁÁÁ
11–14 v
ÁÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁÁ
Go to Step 8
ÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁ
Go to Step 9
ÁÁ
ÁÁ
8
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
1. Replace the SIR wiring harness.
2. Reconnect the battery.
Is the repair complete?
ÁÁÁ
ÁÁÁ
–
ÁÁÁÁÁ
ÁÁÁÁÁ
Go to
Diagnostic
System Check
ÁÁÁÁ
ÁÁÁÁ
–
ÁÁ
ÁÁ
9
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
Repair the open circuit between the fuse F2 and the
connector C208.
Is the repair complete?
ÁÁÁ
ÁÁÁ
–
ÁÁÁÁÁ
ÁÁÁÁÁ
Go to
Diagnostic
System Check
ÁÁÁÁ
ÁÁÁÁ
–