18-4
D Command table (continued)
18
CONTROL COMMAND
Cmd. Sub Cmd. Data Description
15 01 00 Read noise or S-meter squelch status
(squelch close)
01 Read noise or S-meter squelch status
(squelch open)
02 0000 to
0255
Read S-meter level
(0000=S0, 0120=S9, 0241=S9+60 dB)
05 00 Read various squelch (tone squelch, and so
on) status (squelch close)
01 Read various squelch (tone squelch, and so
on) status (squelch open)
11 0000 to
0255
Read RF power meter
(0000=0 W, 0143=100 W, 0213=200 W)
12 0000 to
0255
Read SWR meter
( 0000=SWR1.0, 0048=SWR1.5,
0080=SWR2.0, 0120=SWR3.0)
13 0000 to
0255
Read ALC meter (0000=0, 0120=Max.)
14 0000 to
0255
Read COMP meter
(0000=0 dB, 0130=15 dB, 0241=30 dB)
15 0000 to
0255
Read VD meter
(0151=44 V, 0180=48 V, 0211=52 V)
16 0000 to
0255
Read ID meter
( 0000=0 A, 0097=10 A, 0146=15 A,
0241=25 A)
16* 02 00 Preamp OFF
01 Preamp 1 ON
02 Preamp 2 ON
12 00 AGC OFF selection
01 AGC FAST selection
02 AGC MID selection
03 AGC SLOW selection
22 00 Noise blanker OFF
01 Noise blanker ON
32 00 Audio peak filter OFF
01 Audio peak filter WIDE ON
(320 Hz is selected when SHARP APF is set)
02 Audio peak filter MID ON
(160 Hz is selected when SHARP APF is set)
03 Audio peak filter NAR ON
(80 Hz is selected when SHARP APF is set)
40 00 Noise reduction OFF
01 Noise reduction ON
41 00 Auto notch function OFF
01 Auto notch function ON
42 00 Repeater tone OFF
01 Repeater tone ON
43 00 Tone squelch OFF
01 Tone squelch ON
44 00 Speech compressor OFF
01 Speech compressor ON
45 00 Monitor function OFF
01 Monitor function ON
46 00 VOX function OFF
01 VOX function ON
47 00 BK-IN function OFF
01 Semi BK-IN function ON
02 Full BK-IN function ON
48 00 Manual notch function OFF
01 Manual notch function ON
4C 00 VSC function OFF
01 VSC function ON
4D 00 AGC VR function OFF
01 AGC VR function ON
4E 00 DIGI-SEL function OFF
01 DIGI-SEL function ON
4F 00 Twin peak filter OFF
01 Twin peak filter ON
( Can be turned ON only when Mark and Shift
are set to 2125 Hz and 170 Hz, respectively)
16* 50 00 Dial lock function OFF
01 Dial lock function ON
*
1
In the CW mode, if the [TRANSMIT] or an external TX switch is ON, or
the Break-in function is ON, a message will be transmitted as CW code
when you send it from your PC.
*
2
The power ON command (18 01) is available only when the transceiver is
standby mode.
Cmd. Sub Cmd. Data Description
16* 53 00 ANT-RX I/O setting OFF
01 ANT-RX I/O setting “A”
02 ANT-RX I/O setting “B”
55 00 15 kHz roofing filter selection
01 6 kHz roofing filter selection
02 3 kHz roofing filter selection
03 1.2 kHz roofing filter selection
56 00 SHARP selection for DSP filter type
01 SOFT selection for DSP filter type
57 00 WIDE selection for manual notch width
01 MID selection for manual notch width
02 NAR selection for manual notch width
58 00 WIDE selection for SSB transmit bandwidth
01 MID selection for SSB transmit bandwidth
02 NAR selection for SSB transmit bandwidth
17 see p. 18-12 Send CW messages*
1
18 00 Turn OFF the transceiver
01 Turn ON the transceiver*
2
19 00 Read the transceiver ID
1A* 00 see p. 18-13 Send/read memory contents
01 see p. 18-10 Send/read band stacking register contents
02 see p. 18-10 Send/read memory keyer contents
03 00 to 49 Send/read the selected filter width
( AM: 00=200 Hz to 49=10 kHz; Other than
AM: 00=50 Hz to 31=2700 Hz/40=3600 Hz)
04 00 to 13 Send/read the selected AGC time constant
( 00=OFF, AM: 01=0.1 sec. to 13=6.0 sec.,
SSB, CW, RTTY: 01=0.3 sec. to
13=6.0/8.0 sec.)
05 0001 see p. 18-12 Send/read SSB RX HPF/LPF settings
0002 00 to 10 Send/read SSB RX Tone (Bass) level
(00 =–5 to 10=+5)
0003 00 to 10 Send/read SSB RX Tone (Treble) level
(00=–5 to 10=+5)
0004 see p. 18-11 Send/read AM RX HPF/LPF settings
0005 00 to 10 Send/read AM RX Tone (Bass) level
(00 =–5 to 10=+5)
0006 00 to 10 Send/read AM RX Tone (Treble) level
(00=–5 to 10=+5)
0007 see p. 18-11 Send/read FM RX HPF/LPF settings
0008 00 to 10 Send/read FM RX Tone (Bass) level
(00 =–5 to 10=+5)
0009 00 to 10 Send/read FM RX Tone (Treble) level
(00=–5 to 10=+5)
0010 see p. 18-11 Send/read CW RX HPF/LPF settings
0011 see p. 18-11 Send/read RTTY RX HPF/LPF settings
0012 see p. 18-11 Send/read PSK RX HPF/LPF settings
0013 00 to 10 Send/read SSB TX Tone (Bass) level
(00 =–5 to 10=+5)
0014 00 to 10 Send/read SSB TX Tone (Treble) level
(00=–5 to 10=+5)
0015 00 to 10 Send/read AM TX Tone (Bass) level
(00 =–5 to 10=+5)
0016 00 to 10 Send/read AM TX Tone (Treble) level
(00=–5 to 10=+5)
0017 00 to 10 Send/read FM TX Tone (Bass) level
(00 =–5 to 10=+5)
0018 00 to 10 Send/read FM TX Tone (Treble) level
(00=–5 to 10=+5)
0019 see p. 18-11 Send/read SSB TX bandwidth for wide
0020 see p. 18-11 Send/read SSB TX bandwidth for mid.
0021 see p. 18-11 Send/read SSB TX bandwidth for narrow
0022 0000 to
0255
Send/read speech level
(0000=0% to 0255=100%)
1A* 05 0023 0000 to
0255
Send/read CW side tone gain
(0000=0% to 0255=100%)
To Next Page
Loading...
Need help?
General
