Inovance Monarch 220-NICE-L-C-4022F User Manual

3 Peripheral Devices and Options
-
116
-
3.3.3 Display Board (MCTC-HCB)
As an important interface between users and the control system, the MCTC-HCB
󶍿
This board can also be used as car display board.
Inovance provides many types of display boards. The following part describes only
two common types. If the types available cannot meet your requirements, you can use
a parallel-serial conversion board (HCB-B)
to make the board provided match your own. For any further requirement, refer to the
MCTC-HCB Display Board Selection Manual with data code 19010457.
󶙽Common MCTC-HCB types
Name Description Size (mm)
MCTC-HCB-H Dot-matrix display board (red) 144 × 70 × 18
MCTC-HCB-R1
Ultrathin dot-matrix display board
(red)
144 × 70 × 10
MCTC-HCB-H: Dot-matrix display board
■
Appearance and dimensions
22.9
56.
0
144.0
70.0
134.0
22.
9
39.1
34
.3
S1
CN1
JP1
JP2
JP3
JP
4
UP
DOWN
MCTC-
HCB
-H
4-Φ
4.2
9.9
22.5
1
2
MCTC-HCB-H
1 - Plastic support higher than 1 cm
2 - Self-tapping screw 4-φ4.9x30
󶙽Appearance, dimensions, and installation method of MCTC-HCB-H

Inovance Monarch 220-NICE-L-C-4022F Specifications

General

Product name	Inovance Monarch 220-NICE-L-C-4022F
Model	220-NICE-L-C-4022F
Rated voltage	220V
Control mode	Vector control
Application	Industrial automation
Output Current	2.2 A
Control Method	V/F control, Sensorless vector control
Communication Interface	Modbus RTU
Protection Features	Overcurrent, Overvoltage, Overheat, Short circuit
Humidity	5% to 95% (non-condensing)

Summary

Preface

1 More advanced technology

Details the advanced technological features of the NICE3000new controller, including drive ride and communication.

3 Safer running

Focuses on safety features, fault tolerance, and environmental adaptability for secure operation.

Introduction

1 Basic functions

Details fundamental functionalities like collective selective operation, service floor settings, and door control.

1 Product Information

1.1 Designation Rule and Nameplate

Explains the model designation rules and details found on the controller's nameplate.

1.2 Description of components

Provides an overview of the physical components of the controller, illustrating their locations.

1.3 Technical Data

1.4 Technical Specifications

1.5 System Configuration

Illustrates the system components and their interconnections for the NICE3000new control system.

2 Installation and Wiring

2.1 Installation

Covers installation requirements, including environment, clearance, orientation, dimensions, and procedures.

2.2 Wiring

Describes the description and wiring of main circuit and control circuit terminals, including cable sizes.

2.3 Interface and Communication

2.4 Installation of Shaft Position Signals

2.5 Standard Wiring of the System

Provides wiring diagrams and inspection checklists for the entire system setup.

3 Peripheral Devices and Options

3.1 Peripheral Devices

3.2 Peripheral Device Selection Guide

Offers guidance on selecting cables, circuit breakers, contactors, reactors, and filters.

4 Commissioning Tools

4.1 Keypad

4.2 Operation Panel

5 System Commissioning

5.1 System Commissioning Guide

Provides a general guide to the commissioning process for the elevator system.

5.2 Safety and Circuit Check

Details crucial safety precautions and checks required before performing system commissioning.

5.3 Power-on and Controller State Check

Covers procedures for checking power-on status and handling potential controller states and faults.

5.4 Commissioning at Inspection Speed

Explains the process of motor auto-tuning and running tests at inspection speed.

5.5 Commissioning at Normal Speed

Outlines steps for commissioning at normal speed, including shaft auto-tuning and HCB setup.

5.6 Riding Comfort Adjustment

6 Parameter Description

6.1 Keypad

6.2 Operation Panel

7 Troubleshooting

7.1 Elevator Fault Display

Explains how fault codes and subcodes are displayed on the keypad and operation panel.

7.2 Restart after Fault

7.4 Fault Information and Troubleshooting

Provides a table linking fault codes to possible causes and recommended solutions for troubleshooting.

9 Description of Functions and Schemes

9.2 Fire Emergency Running

9.10 UCMP Function

9.13 Automatic Emergency Evacuation Scheme at Power Failure

Details how the system provides emergency evacuation during power failures using UPS or ARD.

9.14 Parallel/Group Control Scheme

9.15 Opposite Door Control Scheme

9.16 STO Application Scheme