Inovance Monarch 220-NICE-L-C-4022F User Manual

4 Commissioning Tools
-
138
-
4.2.3 Data Display
󶍾
output frequency, all kinds of monitoring data, and fault codes.
󶙽LED display and actual data
LED
Display
Actual
Data
LED
Display
Actual
Data
LED
Display
Actual
Data
LED
Display
Actual
Data
0 6 C N
1 7 c P
2 8 D R
3 9 E T
4 A F U
5, S B L u
4.2.4 Basic Operations
The operation panel adopts the following three-level menus.
■
Level I: function code group
■
Level II: function code
■
Level III: function code setting value
Level II menu
F0
F1
PRG
F0-
00
F9
FA
.
.
.
.
.
.
Power-on or after
factory reset
PRG
FP
FP
.
.
.
FA
F9
.
.
.
F0
F0-01
F0-
07
.
.
.
F0-07
.
.
.
F0
-01
ENTER
PRG
1
.
.
.
.
.
.
F0-01
PRG
ENTER
ENTER
ENTER
Level I menu Level III menu
0.000
Function code
group
Function code
Function
parameter value
1 Parameter display
󶍾
󶍾-
rameter contents (For details, refer to the description of parameters). If a bit is set to 1,
the parameter indicated by this bit is displayed; if this bit is set to 0, the parameter is
not displayed.

Inovance Monarch 220-NICE-L-C-4022F Specifications

General

Product name	Inovance Monarch 220-NICE-L-C-4022F
Model	220-NICE-L-C-4022F
Rated voltage	220V
Control mode	Vector control
Application	Industrial automation
Output Current	2.2 A
Control Method	V/F control, Sensorless vector control
Communication Interface	Modbus RTU
Protection Features	Overcurrent, Overvoltage, Overheat, Short circuit
Humidity	5% to 95% (non-condensing)

Summary

Preface

1 More advanced technology

Details the advanced technological features of the NICE3000new controller, including drive ride and communication.

3 Safer running

Focuses on safety features, fault tolerance, and environmental adaptability for secure operation.

Introduction

1 Basic functions

Details fundamental functionalities like collective selective operation, service floor settings, and door control.

1 Product Information

1.1 Designation Rule and Nameplate

Explains the model designation rules and details found on the controller's nameplate.

1.2 Description of components

Provides an overview of the physical components of the controller, illustrating their locations.

1.3 Technical Data

1.4 Technical Specifications

1.5 System Configuration

Illustrates the system components and their interconnections for the NICE3000new control system.

2 Installation and Wiring

2.1 Installation

Covers installation requirements, including environment, clearance, orientation, dimensions, and procedures.

2.2 Wiring

Describes the description and wiring of main circuit and control circuit terminals, including cable sizes.

2.3 Interface and Communication

2.4 Installation of Shaft Position Signals

2.5 Standard Wiring of the System

Provides wiring diagrams and inspection checklists for the entire system setup.

3 Peripheral Devices and Options

3.1 Peripheral Devices

3.2 Peripheral Device Selection Guide

Offers guidance on selecting cables, circuit breakers, contactors, reactors, and filters.

4 Commissioning Tools

4.1 Keypad

4.2 Operation Panel

5 System Commissioning

5.1 System Commissioning Guide

Provides a general guide to the commissioning process for the elevator system.

5.2 Safety and Circuit Check

Details crucial safety precautions and checks required before performing system commissioning.

5.3 Power-on and Controller State Check

Covers procedures for checking power-on status and handling potential controller states and faults.

5.4 Commissioning at Inspection Speed

Explains the process of motor auto-tuning and running tests at inspection speed.

5.5 Commissioning at Normal Speed

Outlines steps for commissioning at normal speed, including shaft auto-tuning and HCB setup.

5.6 Riding Comfort Adjustment

6 Parameter Description

6.1 Keypad

6.2 Operation Panel

7 Troubleshooting

7.1 Elevator Fault Display

Explains how fault codes and subcodes are displayed on the keypad and operation panel.

7.2 Restart after Fault

7.4 Fault Information and Troubleshooting

Provides a table linking fault codes to possible causes and recommended solutions for troubleshooting.

9 Description of Functions and Schemes

9.2 Fire Emergency Running

9.10 UCMP Function

9.13 Automatic Emergency Evacuation Scheme at Power Failure

Details how the system provides emergency evacuation during power failures using UPS or ARD.

9.14 Parallel/Group Control Scheme

9.15 Opposite Door Control Scheme

9.16 STO Application Scheme