Yealink SIP-T33P Administrator's Guide

Phone Customization
238
Softkey Layout Configuration
The following table lists the parameters you can use to configure the softkey layout.
Parameter
phone_setting.custom_softkey_enable <y0000000000xx>.cfg
Description
It enables or disables the custom soft keys layout feature.
Permitted
Values
0-Disabled
1-Enabled
Default
0
Web UI
Settings > Softkey Layout > Custom SoftKey
Parameter
phone_setting.custom_softkey.apply_to_states <y0000000000xx>.cfg
Description
It configures the desired call state to apply the custom softkey layout.
To configure the call states to apply the custom softkey layout:
Example:
phone_setting.custom_softkey.apply_to_states = DialingEmpty,DialTransEmpty
It means that DialingEmpty and DialTransEmpty call states will use the custom softkey layout.
To configure the call states not to apply the custom softkey layout:
Example:
phone_setting.custom_softkey.apply_to_states = -DialingEmpty,DialTransEmpty
It means that DialingEmpty and DialTransEmpty call states will not use the custom softkey layout.
Note: Multiple call states are separated by commas. It works only if “phone_setting.custom_softkey_
enable” is set to 1 (Enabled).
Permitted
Values
Blank (all call states will use the custom softkey layout)
Dialing, DialingEmpty, DialTrans, DialTransEmpty, DialConference, DialConferenceEmpty, Talk,
Hold, Held, CallIn, NewCallIn, BeTransferred, SemiAttendTrans, Conferenced, ConferencedHold,
ConferencedNewCallIn, Connecting, CallFailed, Paging, ListeningPaging, RingBack, SemiAt-
tendTransBack
Default
Blank
Parameter
features.custom_softkey_dynamic.enable <y0000000000xx>.cfg
Description
It enables or disables the phone to display the soft keys relevant to the features (call center, cent-
ralized call recording, and executive-assistant).
Note: It works only if “phone_setting.custom_softkey_enable” is set to 1 (Enabled).
Permitted
Values
0-Disabled
1-Enabled, the functional soft keys display on the phone screen if the corresponding feature is avail-
able.
Default
1
Parameter
custom_softkey_call_failed.url <y0000000000xx>.cfg
Description
It configures the access URL of the custom softkey layout file in the CallFailed state.
Note: It works only if “phone_setting.custom_softkey_enable” is set to 1 (Enabled).
Permitted
Values
URL within 511 characters

Yealink SIP-T33P Specifications

General

Mounting	Desk/Wall
Handset type	Wired handset
Product type	IP Phone
Product color	Gray
Wall mountable	Yes
Operating system installed	Linux
Lines quantity	4 lines
Phonebook capacity	1000 entries
Number of VoIP accounts	4
Volume control	Buttons
Number of function keys	5
Display diagonal	2.4 \
Display resolution	320 x 240 pixels
Voice codecs	AGC, AJB, CNG, G.711a, G.711u, G.722, G.723.1, G.726, G.729, G.729A, PLC, VAD, iLBC
Security algorithms	AES, HTTPS
Ethernet LAN data rates	10, 100 Mbit/s
Ethernet LAN interface type	Fast Ethernet
RJ-9 ports quantity	1
Ethernet LAN (RJ-45) ports	2
Input frequency	50/60 Hz
AC adapter input voltage	100 - 240 V
Power consumption (typical)	3 W
Power consumption (Power over Ethernet (PoE))	5 W
Number of handles included	1 pc(s)
Operating temperature (T-T)	-10 - 50 °C
Operating relative humidity (H-H)	10 - 95 %

Weight and Dimensions

Depth	186 mm
Width	212 mm
Height	146 mm