Yealink SIP-T33P Administrator's Guide

Administrator’s Guide for SIP-T2 /T3 /T4 /T5 /CP920 IP Phones
395
Description
It enables or disables the DND feature synchronization for account X.
Note: The value configured by this parameter takes precedence over that configured by the parameter
"features.dnd.feature_key_sync.enable". It works only if “account.X.feature_key_sync.enable” is set to
1 (Enabled).
Permitted
Values
0-Disabled
1-Enabled, server-based DND is enabled. Server and local phone DND are synchronized.
Default
Blank
Supported
Devices
All phones except T48G, T46G, T42G, T41P, T29G and CP920
Parameter
features.dnd.feature_key_sync.local_processing.enable <y0000000000xx>.cfg
Description
It enables or disables the local DND when DND feature synchronization is enabled.
Note: It works only if “features.feature_key_sync.enable” and “features.dnd.feature_key_sync.enable”
are set to 1 (Enabled). The value configured by the parameter “account.X.features.dnd.feature_key_
sync.local_processing.enable” takes precedence over that configured by this parameter.
Permitted
Values
0-Disabled, DND is performed on the server side only.
1-Enabled, DND is performed on both the server side and locally.
Default
0
Parameter
account.X.features.dnd.feature_key_sync.local_processing.enable
[1]
<MAC>.cfg
Description
It enables or disables the local DND when DND feature synchronization is enabled.
Note: It works only if “features.feature_key_sync.enable” and “features.dnd.feature_key_sync.enable”
are set to 1 (Enabled).
Permitted
Values
0-Disabled, DND is performed on the server side only.
1-Enabled, DND is performed on both the server side and locally.
Default
Blank
[1]
X is the account ID. For T57W/T54W/T48U/T48S/T48G/T46U/T46S/T46G/T29G, X=1-16; for
T53W/T53/T43U/T42U/T42G/T42S, X=1-12; for T41P/T41S/T27G, X=1-6; for T33P/T33G, X=1-4; for
T40P/T40G/T23P/T23G, X=1-3; for T31P/T31G/T31/T21(P) E2, X=1-2.
Multiple Call Appearances
You can enable each registered line to support multiple concurrent calls. For example, you can place one call on
hold, switch to another call on the same registered line, and have both calls displayed.
You can set the maximum number of concurrent calls per line key on all-lines basis or a per-line basis. For
example, if you specify 3 concurrent-calls for account 1, you can only have three call appearances on a cor-
responding line key. The additional incoming calls will be rejected.
Note: The number of concurrent calls applies to all line keys. For example, if three line keys are associated with an account,
you can have three call appearances per line key.
Topic
Multiple Call Appearances Configuration
Multiple Call Appearances Configuration
You can specify the maximum concurrent calls per line key.
The following table lists the parameters you can use to configure multiple call appearances.

Yealink SIP-T33P Specifications

General

Mounting	Desk/Wall
Handset type	Wired handset
Product type	IP Phone
Product color	Gray
Wall mountable	Yes
Operating system installed	Linux
Lines quantity	4 lines
Phonebook capacity	1000 entries
Number of VoIP accounts	4
Volume control	Buttons
Number of function keys	5
Display diagonal	2.4 \
Display resolution	320 x 240 pixels
Voice codecs	AGC, AJB, CNG, G.711a, G.711u, G.722, G.723.1, G.726, G.729, G.729A, PLC, VAD, iLBC
Security algorithms	AES, HTTPS
Ethernet LAN data rates	10, 100 Mbit/s
Ethernet LAN interface type	Fast Ethernet
RJ-9 ports quantity	1
Ethernet LAN (RJ-45) ports	2
Input frequency	50/60 Hz
AC adapter input voltage	100 - 240 V
Power consumption (typical)	3 W
Power consumption (Power over Ethernet (PoE))	5 W
Number of handles included	1 pc(s)
Operating temperature (T-T)	-10 - 50 °C
Operating relative humidity (H-H)	10 - 95 %

Weight and Dimensions

Depth	186 mm
Width	212 mm
Height	146 mm