Yealink SIP-T33P Administrator's Guide

Phone Customization
280
Note: It works only if “features.enhanced_dss_keys.enable” and “edk.edkprompt.X.enable” are set to
1 (Enabled).
Permitted
Values
String
Default
EDK Prompt
Supported
Devices
All phones except T57W, T48U, T48S, T48G, T46G, T42G, T41P, T29G
[1]
X is the prompt ID. X=1-10.
EDK Soft Keys Configuration
You can customize the soft keys as need. This feature is typically used to access frequently-used functions or to cre-
ate menu shortcuts to frequently-used phone settings.
Custom soft keys can be added in the following phone states:
l
Idle - There are no active calls on the phone.
l
Alerting (or ringing) – There is an incoming call on the phone.
l
Connecting – There is an outgoing call on the phone. Moreover, the call is connecting.
l
Transfer connecting – There is a call being transferred to another phone. Moreover, the call is connecting.
l
Talk – There is an active call on the phone.
l
Call failed – The outgoing call encounters a failure.
l
Ring back - There is an outgoing call on the phone. Moreover, the phone is in the ringback state.
l
Transfer ring back - There is a call being transferred to another phone. Moreover, the phone is in the ringback
state.
l
Hold – The call is placed on hold on the phone.
l
Held – The call is held.
l
Conference – The phone sets up a conference call.
l
Dial tone –The phone is on the dialing screen without entering the number.
l
Dialing – The phone is on the dialing screen with entering the number but not dialing.
Note: Configuring the custom soft keys may affect the softkey layout in different call states. For more information on softkey
layout, refer to Softkey Layout.
The following table lists the parameters you can use to configure EDK soft keys.
Parameter
softkey.X.enable
[1]
<y0000000000xx>.cfg
Description
It enables or disables the custom soft key X.
Note: It works only if “features.enhanced_dss_keys.enable” is set to 1 (Enabled).
Permitted
Values
0-Disabled
1-Enabled
Default
0
Parameter
softkey.X.label
[1]
<y0000000000xx>.cfg
Description
It configures the text displayed on the soft key label.
Note: It works only if “features.enhanced_dss_keys.enable” and “softkey.X.enable” are set to 1
(Enabled).
Permitted
Values
String
Default
Blank
Parameter
softkey.X.position
[1]
<y0000000000xx>.cfg

Yealink SIP-T33P Specifications

General

Mounting	Desk/Wall
Handset type	Wired handset
Product type	IP Phone
Product color	Gray
Wall mountable	Yes
Operating system installed	Linux
Lines quantity	4 lines
Phonebook capacity	1000 entries
Number of VoIP accounts	4
Volume control	Buttons
Number of function keys	5
Display diagonal	2.4 \
Display resolution	320 x 240 pixels
Voice codecs	AGC, AJB, CNG, G.711a, G.711u, G.722, G.723.1, G.726, G.729, G.729A, PLC, VAD, iLBC
Security algorithms	AES, HTTPS
Ethernet LAN data rates	10, 100 Mbit/s
Ethernet LAN interface type	Fast Ethernet
RJ-9 ports quantity	1
Ethernet LAN (RJ-45) ports	2
Input frequency	50/60 Hz
AC adapter input voltage	100 - 240 V
Power consumption (typical)	3 W
Power consumption (Power over Ethernet (PoE))	5 W
Number of handles included	1 pc(s)
Operating temperature (T-T)	-10 - 50 °C
Operating relative humidity (H-H)	10 - 95 %

Weight and Dimensions

Depth	186 mm
Width	212 mm
Height	146 mm