Yealink SIP-T33P Administrator's Guide

Call Features
366
Permitted
Values
0-Disabled
1-Enabled, the incoming calls will be forwarded to the desired destination number according to the
string of the digit map.
Default
1
Parameter
dialplan.digitmap.apply_to.press_send <y0000000000xx>.cfg
Description
It enables or disables the entered number to match the predefined string of the digit map after press-
ing a send key. It is only applicable to the off-hook dialing.
The off-hook dialing includes: pick up the handset, press the Speakerphone key or press the line key
when the phone is idle.
Note: It works only if “dialplan.digitmap.enable” or “account.X.dialplan.digitmap.enable” is set to 1
(Enabled). The value configured by the parameter “account.X.dialplan.digitmap.apply_to.press_send”
takes precedence over that configured by this parameter.
Permitted
Values
0-Disabled
1-Enabled
Default
1
Parameter
dialplan.digitmap.apply_to.prefix_key <y0000000000xx>.cfg
Description
It enables or disables the phone to apply the predefined string of the digit map after pressing a Prefix
key.
Note: It works only if “dialplan.digitmap.enable” or “account.X.dialplan.digitmap.enable” is set to 1
(Enabled).
Permitted
Values
0-Disabled
1-Enabled
Default
1
Digit Map for a Specific Line Configuration
The following table lists the parameters you can use to configure the digit map for a specific line.
Parameter
account.X.dialplan.digitmap.enable
[1]
<MAC>.cfg
Description
It enables or disables the digit map feature for a specific account.
Note: The value configured by the parameter “account.X.dialplan.digitmap.enable” takes precedence
over that configured by the parameter “dialplan.digitmap.enable”.
Permitted
Values
0-Disabled
1-Enabled
Default
Blank
Parameter
account.X.dialplan.digitmap.string
[1]
<MAC>.cfg
Description
It configures the digit map pattern used for the dial plan.
Example:
account.1.dialplan.digitmap.string = <[2-9]x:86>3.T|0x.!|1xxx
Note: The string must be compatible with the digit map feature of MGCP described in 2.1.5 of RFC
3435. It works only if “account.X.dialplan.digitmap.enable” is set to 1 (Enabled). The value configured
by the parameter “account.X.dialplan.digitmap.string” takes precedence over that configured by the
parameter “dialplan.digitmap.string”.
Permitted
Values
String within 2048 characters

Yealink SIP-T33P Specifications

General

Mounting	Desk/Wall
Handset type	Wired handset
Product type	IP Phone
Product color	Gray
Wall mountable	Yes
Operating system installed	Linux
Lines quantity	4 lines
Phonebook capacity	1000 entries
Number of VoIP accounts	4
Volume control	Buttons
Number of function keys	5
Display diagonal	2.4 \
Display resolution	320 x 240 pixels
Voice codecs	AGC, AJB, CNG, G.711a, G.711u, G.722, G.723.1, G.726, G.729, G.729A, PLC, VAD, iLBC
Security algorithms	AES, HTTPS
Ethernet LAN data rates	10, 100 Mbit/s
Ethernet LAN interface type	Fast Ethernet
RJ-9 ports quantity	1
Ethernet LAN (RJ-45) ports	2
Input frequency	50/60 Hz
AC adapter input voltage	100 - 240 V
Power consumption (typical)	3 W
Power consumption (Power over Ethernet (PoE))	5 W
Number of handles included	1 pc(s)
Operating temperature (T-T)	-10 - 50 °C
Operating relative humidity (H-H)	10 - 95 %

Weight and Dimensions

Depth	186 mm
Width	212 mm
Height	146 mm