Yealink SIP-T33P Administrator's Guide

Administrator’s Guide for SIP-T2 /T3 /T4 /T5 /CP920 IP Phones
363
“<9,:55>xx”, after entering digit “9”, secondary dial tone plays and you can complete the remaining two-
digit number.
Note: The secondary dial tone can be customized. For more information, refer to Tones.
A
The letter “A” indicates the account that is applied to the digit map. You can use A alone or a com-
bination of A and account ID (for example, <A1>).
Example:
“123A”, the default account will be applied to the digit map.
“123<A2>”, the second account will be applied to the digit map.
Note: It is not applicable to the digit map on a per-line basis.
Digit Map for All Lines Configuration
The following table lists the parameters you can use to configure the digit map for all lines.
Parameter
dialplan.digitmap.enable <y0000000000xx>.cfg
Description
It enables or disables the digit map feature.
Note: The value configured by the parameter “account.X.dialplan.digitmap.enable” takes precedence
over that configured by this parameter.
Permitted
Values
0-Disabled
1-Enabled
Default
0
Parameter
dialplan.digitmap.string <y0000000000xx>.cfg
Description
It configures the digit map pattern used for the dial plan.
Example:
dialplan.digitmap.string = <[2-9]x:86>3.T|0x.!|1xxx
Note: The string must be compatible with the digit map feature of MGCP described in 2.1.5 of RFC
3435. It works only if “dialplan.digitmap.enable” or “account.X.dialplan.digitmap.enable” is set to 1
(Enabled). The value configured by the parameter “account.X.dialplan.digitmap.string” takes pre-
cedence over that configured by this parameter.
Permitted
Values
String within 2048 characters
Default
[2-9]11 | 0T | 011xxx.T | [0-1][2-9]xx xxxxxxx | [2-9]xx xxxxxxx | [2-9]xxxT | **x.T | +x.T| 00x.T
Parameter
dialplan.digitmap.interdigit_long_timer <y0000000000xx>.cfg
Description
It configures the time (in seconds) for the phone to wait before dialing an entered number if it matches
part of any string of the digit map.
If it is set to 0, the phone will not dial the entered number if only a partial match exists.
The value of this parameter should be greater than that configured by the parameter “dial-
plan.digitmap.interdigit_short_timer”.
For example:
dialplan.digitmap.string = 1xxT|xxxxx<T1>
dialplan.digitmap.interdigit_long_timer = 10
dialplan.digitmap.interdigit_short_timer = 5
When you enter 1, it matches part of two-digit maps, the phone tries to wait 10 seconds and then dials

Yealink SIP-T33P Specifications

General

Mounting	Desk/Wall
Handset type	Wired handset
Product type	IP Phone
Product color	Gray
Wall mountable	Yes
Operating system installed	Linux
Lines quantity	4 lines
Phonebook capacity	1000 entries
Number of VoIP accounts	4
Volume control	Buttons
Number of function keys	5
Display diagonal	2.4 \
Display resolution	320 x 240 pixels
Voice codecs	AGC, AJB, CNG, G.711a, G.711u, G.722, G.723.1, G.726, G.729, G.729A, PLC, VAD, iLBC
Security algorithms	AES, HTTPS
Ethernet LAN data rates	10, 100 Mbit/s
Ethernet LAN interface type	Fast Ethernet
RJ-9 ports quantity	1
Ethernet LAN (RJ-45) ports	2
Input frequency	50/60 Hz
AC adapter input voltage	100 - 240 V
Power consumption (typical)	3 W
Power consumption (Power over Ethernet (PoE))	5 W
Number of handles included	1 pc(s)
Operating temperature (T-T)	-10 - 50 °C
Operating relative humidity (H-H)	10 - 95 %

Weight and Dimensions

Depth	186 mm
Width	212 mm
Height	146 mm